Filter
Top Products
CETTF10xx-105
6
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Operation -- Continued
Product Features
AutoCross™
When the AutoCross feature is activated, it allows either straight-through
(MDI) or crossover (MDI-X) copper cables to be used when connecting to
10Base-T devices. AutoCross determines the characteristics of the connection
and automatically configures the unit to link up, regardless if the copper cable
is MDI or MDI-X configuration.
NOTE: Factory default is “enable AutoCross.” Transition networks
recommends leaving the device in the “enable” mode.
Link Pass Through
The Link Pass-Through feature allows the media converter to monitor both the
fiber and copper RX (receive) ports for loss of signal. In the event of a loss of
an RX signal (1), the media converter will automatically disable the TX
(transmit) signal (2), thus, “passing through” the link loss (3). The far-end
device is automatically notified of the link loss (4), which prevents the loss of
valuable data unknowingly transmitted over an invalid link.
NOTE: An enable/disable switch allows the Link Pass Through feature to be
disabled. Link Pass Through may interfere with the Auto-Negotiation feature
of other devices in networks where there are two media converters installed in
series.
4
1
Media
Converter A
Media
Converter B
Near-End
Device
Far-End
Device
original fault
on the copper link
media converter B
disables the copper lin
k
media converter A
disables the fiber TX link
3
2
media converter B
loses the fiber RX link
7
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
Cable Specifications
The physical characteristics must meet or exceed IEEE 802.3™ specifications.
Fiber Cable
Bit Error Rate: <10-9
Single mode fiber (recommended): 9 µm
Multimode fiber (recommended): 62.5/125 µm
Multimode fiber (optional): 100/140, 85/140, 50/125 µm
CETTF1011-105 850 nm multimode
CETTF1013-105 850 nm multimode
Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm
Fiber Optic Receiver Sensitivity: min: -32.5 dBm max: -14.0 dBm
Link Budget: 13.5 dB
CETTF1012-105 1310 nm single mode
Fiber Optic Transmitter Power: min: -27.0 dBm max: -10.0 dBm
Fiber Optic Receiver Sensitivity: min: -34.0 dBm max: -14.0 dBm
Link Budget: 7.0 dB
CETTF1014-105 1310 nm single mode
CETTF1014-106 1310 nm single mode
Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm
Fiber Optic Receiver Sensitivity: min: -34.0 dBm max: -3.0 dBm
Link Budget: 15.0 dB
CETTF1015-105 1310 nm single mode
Fiber Optic Transmitter Power: min: -15.0 dBm max: -8.0 dBm
Fiber Optic Receiver Sensitivity: min: -38.0 dBm max: -8.0 dBm
Link Budget: 23.0 dB
CETTF1018-105 850 nm multimode
Fiber Optic Transmitter Power: min: -16.0 dBm max: -10.0 dBm
Fiber Optic Receiver Sensitivity: min: -29.5 dBm max: -7.2 dBm
Link Budget: 13.5 dB
CETTF1022-105 1310 nm single mode
Fiber-optic Transmitter Power: min: -15.0 dBm max: -5.0 dBm
Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -14.0 dBm
Link Budget: 19.0 dB
CETTF1027-105 1300 nm multimode
Fiber-optic Transmitter Power: min: -19.0 dBm max: -15.0 dBm
Fiber-optic Receiver Sensitivity: min: -32.5 dBm max: -14.0 dBm
Link Budget:
13.5 dB
CETTF1029-105 1310 nm (TX) / 1550 nm (RX) simplex
CETTF1029-106 1550 nm (TX) / 1310 nm (RX) simplex
Fiber Optic Transmitter Power: min: -14.0 dBm max: -8.0 dBm
Fiber Optic Receiver Sensitivity: min: -33.0 dBm max: -3.0 dBm
Link Budget: 19.0 dB
The fiber optic transmitters on this device meets Class I Laser safety
requirements per IEC-825/CDRH standards and complies with 21
CFR1040.10 and 21CFR1040.11.