Filter
Top Products
DIRECTIVES D’USAGE
OPERATING INSTRUCTIONS
Fig. 13
4. Hold the HEPA filter
by the edges and vigorously
“TapClean” the HEPA Filter
dirty side down on a hard,
flat surface until no more
dust is observed falling out
from between the pleats of
the filter. (Fig. 12) We
recommend washing the HEPA filter
once a month or when suction
appears to be reduced. Let the HEPA
filter air dry completely for 24 hours.
5. Rinse the non-woven pre-filter and let
air dry completely for 24 hours.
6. Insert the non-woven pre-filter.
7. Reinstall the HEPA filter in the
vacuum.
8. To separate the debris screen from
the dust cup, hold the dust cup in one
hand and turn the
dust cup cover counter
clockwise and pull apart.
To clean the
debris screen, we
recommend that
you rinse it under
lukewarm running
water to remove the dirt that
accumulates on it, but always allow it
to completely air dry before inserting
back into the vacuum. (Fig. 13)
Warning: Always unplug the
unit from electrical outlet before
opening the Dust Cup (container).
Warning: After each Use -
Always remove Filter Assembly
and the Dust Cup Cover with
the Debris Screen, then
vigorously “TapClean” HEPA
Filter and clean Debris Screen
and Non-Woven Pre-Filter until
no more dust can be removed.
Dust
Cup
Release
Button 2
Dust
Cup
Release
Button 1
Fig. 9
Fig. 10
Fig. 12
Fig. 8
HEPA
Filter
Non-Woven
Pre-Filter
Fig. 11
3. The HEPA filter is
located underneath the
dust cup container. (Fig.10)
Remove the Non-Woven Pre-Filter.
(Fig. 11) Remove the HEPA filter, hold
the edges and pull it out slowly.
Emptying the Dust Cup Container
and Cleaning / Changing the Non-
Woven Pre-Filter, HEPA Filter &
Debris Screen
AVERTISSEMENT: Toujours
débrancher l’aspirateur avant l’assemblage
ou l’enlèvement d’accessoires.
INSÉRER LE TUBE
TÉLESCOPIQUE DANS LE
BOÎTIER PRINCIPAL
• Insérez le tube télescopique dans
l’orifice situé près de la poignée de la
coupelle. Assurez-vous que la fente de
la poignée s’insère bien dans l’orifice
(Fig. 1).
• Pour enlever le tube télescopique,
appuyez sur le bouton de relâche du
tube télescopique et tirez le tube vers
le haut.
EXTENSION DU TUBE
TÉLESCOPIQUE
Appuyez sur le bouton en plastique et
tirez sur le tube le plus petit. Voir
l’illustration ci-dessous.
FIXATION DE LA BROSSE À
PLANCHERS AU BOÎTIER
PRINCIPAL
• Insérez le brosse au bon endroit, dans
le sens de la flèche.
• Pour retirer la brosse du boîtier
principal, appuyez sur le bouton de
relâche de la brosse et tirez la brosse
du boîtier. (Fig. 2)
FIXATION DU BOYAU AU
BOÎTIER PRINCIPAL
• Tenez l’extrémité du boyau.
Insérez le boyau dans le raccord du
boyau (Fig. 3).
Fig. 1
Fig. 2
Fig. 3
2. To empty the dust
cup container,
press on the trap
door release button
that is on the back
side of the dust cup
container. (Fig. 9)
Important: Do NOT use the vacuum
without the HEPA filter in place.
IMPORTANT
, Please Note: The
“TapClean” HEPA Filter will stop most of
the tiniest dust particles and airborne
allergens from re-entering the air you
breathe. In fact it stops 99.97% of all
particles as small as 0.3 microns - many
times smaller than a human hair!!!
Because of this incredible filtration
performance, the HEPA Filter will quickly
accumulate, inside the white filter folds,
many fine dust particles that are difficult to
see but which will eventually block or
reduce your suction power - if not cleaned
properly.
1. To remove the dust cup container,
first press on the dust cup release
button (1) that is located on the dust
cup handle and at the same time
press on the dust cup release button
(2) that is on the side of the upper
housing (Fig. 8). Then pull the dust
cup container out.
26
7