Filter
Top Products
Regency FG39 FireGenie Freestanding Gas Stove
11
INSTALLATION
d) Cut the 2 ft. (.6m) section of rigid pipe
to length. Ensure that the pipe length
when cut will seat onto both the start-
er collar and the 90
o
elbow. Crimped
section of rigid pipe seats into
the 90
o
elbow. Only cut the un-
crimped side of pipe.
Dismantle all pipe sections including flue
terminal.
3) Attach the 4" (102mm) dia. flex liner to the
flue terminal ensuring that the flex overlaps
the collar of the flue terminal by a minimum
of
1-3/8"(35mm). Use Mill-Pac to seal and
secure with 3 of the #8 x 1/2" (13mm)
screws (stainless steel).
4) Attach the 2 ft. (.6m)pipe section to the flue
terminal using Mill-Pac and/or high temper-
ature silicone and attach with 3 of the #8 x
1/2" (13mm) screws (stainless steel).
siding standoff to prevent water from en-
tering and to make a tight seal between the
cap and the standoff.
7) Stretch the 4" (102mm) dia. flex liner out
fully and get a trial fit of the liner onto the 4"
(102mm) dia. starter collar.
8) Cut the 4" (102mm) dia. flex liner to the
desired size.
Hint: leave an extra 12" to 16" (305mm to
406mm) of length, this will make the final
assembly easier to work with.
9) Secure the 4" (102mm) dia. flex liner to the
4" (102mm) adapter with Mill-Pac and 3 of the
#8 x 1/2" (13mm) screws (stainless steel).
10) Slide the Decorative Wall Cover over the
pipe sections.
11) Slide the 90
o
elbow (crimp end up) and the
2 ft. (.6m) pipe section (crimp end up) over
the 4" dia. flex liner.
12) Slide the trim collar over the pipe section to
cover the joint.
13) Install the spring spacers onto the pipe
sections.
14) Secure the 4" (102mm) dia. flex liner with
adapter onto the stove collar. Put a bead of
Mill-Pac around the appliance adapter and
secure with 3 screws (#8 x 1/2" / 13mm,
stainless steel).
15) Attach the pipe section onto the starter
collar by sealing with Mill-Pac and/or high
temperature silicone and securing with 3 of
the #8 x 1/2" (13mm) (black) screws. Pipe
seams should be facing the wall.
16) Attach the 90
o
elbow onto the pipe section
by sealing with Mill-Pac and/or high temper-
ature silicone and securing with 3 of the #8
x 1/2" (13mm) screws (black).
17) Slide the 2 ft. (.6m) pipe section onto the 90
o
elbow. The flex may have to be com-
pressed back in order for the pipe to prop-
erly mate to the elbow. Seal with Mill-Pac
and/or high temperature silicone and se-
cure with 3 of the #8 x 1/2" (13mm) screws
(black). Pipe seams facing down.
18) Install the trim collar over the starter collar
and secure with a #8 x 1/2" (13mm) screw
(black).
If the pipe needs to be touched up, use only
Stove Brite High Temperature Metallic Black
Stove Paint.
NOTE: All inner joints must be sealed
with Mill-Pac.
All outer joints may be sealed with
high temperature silicone.
Note: The pipe seam
should be facing
down.
Note: To make the instal-
lation more aes-
thetically pleasing,
we recommend
framing out a square that the cap
can be mounted on.
Note: If installing termination on a siding
covered wall, a vinyl siding stand-
off or furring strips must be used
to ensure that the termination is
not recessed into the siding. For
vinyl siding standoff installation re-
fer to the Dura-Flue Termination
instructions.
5) Slide the partially connected pipe and flue
terminal assembly through the wall (from
the exterior into the interior) and secure the
cap to the exterior wall with 4 of the supplied
screws (#8 x 1-1/2" (38mm) drill point,
stainless steel).
Note: The four screws provided for the
flue cap should be replaced with
appropriate fasteners for stucco,
brick, concrete, or other types of
sidings.
6) A bead of non-hardening mastic should be
run around both the termination and vinyl
Hint: Apply the
sealant (Mill-
Pac and/or high
temperature sil-
icone) to the
outer pipe be-
fore connecting
the inner pipe.
#8 x ½" (13mm) Self Tapping, Stainless Steel
#8 x ½" Self Tapping, Black(13mm)
#8 x 1½" (38mm) Drill Point, Stainless Steel