Quadra-Fire MTVERNINSAE-PMH Stove User Manual


 
R
November 22, 2011
7036-135G
Page 43
Mt. Vernon Pellet Insert (AE)
11
Reference Materials
9. Firepot
The fi repot is made of high quality ductile iron. The fl oor of
the fi repot automatically opens for cleaning and is operated
by the auto-clean fi repot system. The fl oor needs to return
to a completely closed position or the appliance will not
operate properly.
10. Fuses
There are three fuses. Two fuses are located on the inside
of the control board. One fuse is AC and operates the
igniter and the other fuse is DC and operates all of the
other components. The third fuse is located in the power
supply. A fuse will blow should a short occur and shut off
power to the appliance. The fuses can only be serviced by
an authorized dealer.
11. Heat Exchanger
The heat exchanger is located behind the baffl e and it
transfers heat from the exhaust system into the convection
air chamber. Remove the cast iron baffl e to access the heat
exchanger.
12. Hopper Lid Switch
The hopper lid switch is located on the right side inside the
hopper. It senses whether the hopper lid is open and displays
an icon on the wall control and will turn off the feed motor.
13. Igniter
The igniter is mounted on the base of the fi repot. Combustion
air travels over the red hot igniter creating super heated air
that ignites the pellets.
14. Low Fuel Indicator
The low fuel indication is attached to the left side of the
hopper. It senses the amount of fuel in the hopper and will
display an icon on the wall control when the fuel level is
low.
15. Optical Switch (Auger)
The optical switch is located on top of the feed system and
communicates to the wall control that the auger is spinning
or it has stopped.
16. Power Receptacle
The power receptacle is located on the left side of the
appliance, behind the left cast side panel. Check the wall
receptacle for 120 volt, 60 Hz (standard current). Make sure
the outlet is grounded and has the correct polarity. A good
quality surge protector is highly recommended to protect
the electronics.
When describing the location of a component,
it is always AS YOU FACE THE FRONT OF
THE APPLIANCE.
5. Convection Blower
The convection blower is mounted at the bottom left rear of
the appliance. The convection blower pushes heated air
through the heat exchange system into the room.
6. Door Switch
The door switch is mounted on the right side of the fi rebox
behind the door handle. It senses when the door is open
and will display an icon on the wall control, and will turn off
the auto-clean system and feed motor for safety.
7. Combustion (Exhaust) Blower
The combustion (exhaust) blower is mounted in the bottom
right rearof appliance. The blower is designed to pull the
exhaust from the appliance and push it out through the
venting system.
8. Feed System
The feed system is located on the right side of the appliance
and can be removed as an entire assembly. The assembly
includes the feed motor, mounting bracket, bearing and feed
spring (auger). The hollow feed spring (auger) pulls pellets
up the feed tube from the hopper area and drops them down
the feed chute into the fi repot.
1. Auto-Clean Motor
The auto-clean motor is located under and behind the
repot on the left side, inside the convection air chamber.
It automatically opens and closes the fi repot fl oor so ashes
can fall into the ash pan.
2. Auto-Clean Switch
The auto-clean switch is located on top of the auto-clean
motor. It communicates to the control board when the fi repot
oor is open and when the auto-clean system has completed
its cycle and is back in the home (closed) position.
3. 12 Volt Battery Back-Up Cable (Optional Accessory)
This is an optional accessory. It will plug into the appliance
next to the power outlet located behind the left cast side
panel. An icon will display on the wall control when the
appliance has lost main power and is running on battery
back-up.
4. Control Board
The control board is located on the lower left side of appliance,
behind the left side panel and above the vacuum switch. It
controls the functioning of the appliance and communicates
with the wall control. The control board can only be opened
by an authorized dealer.
A. Component Functions