Filter
Top Products
7
© 2002 Oreck Holdings, LLC. All Rights Reserved. All word mark, logos, product configurations,
and registered trademarks are owned and used under the authorization of Oreck Holdings, LLC.
Printed in U.S.A.
53320-01 REV E 03/02 ECN# R-6359
To Clean Carpet Cleaner
WARNING: To reduce the risk of electric shock or injury from
moving parts, unplug before servicing.
Before turning the cleaner off, tilt the cleaner back, raising the nozzle off
the carpet for 15-20 seconds. This prevents extracted water in the
nozzle from dripping back onto the carpet after you turn the cleaner off.
fig. 13 Place the power switch in the “OFF“ position. Unplug the power
cord from the outlet.
fig. 11 Remove the cleaner cartridge by rotating the locking white lever
upwards. Do not store with a cleaner cartridge attached.
fig. 19 Remove and empty the tank. Rinse out the lower recovery tank
with warm water. Wipe off the inlet screen to remove
accumulated dirt, lint and debris.
fig. 10 Replace tank.
fig. 20 If you have been operating the cleaner at length, it may be
necessary to clean the nozzle from time to time, particularly if the
carpet is brand new or very dirty, or if long-haired pets frequently
use the carpeted area. Unplug cleaner and examine several
areas on the power nozzle to see if debris has built up:
a. Extractor slots
b. Brush roll chamber
c. Spray Tips
fig. 20 To clean the Steemer extractor slots, place a cloth or towel over
the motor cover to shield and protect the motor from water
damage. Run hot tap water through the nozzle until clean.
To clean the brush chamber and spray tips, take a towel or damp
cloth and wipe clean.
To Store Cleaner
fig. 6 Pull the wheel assembly forward toward nozzle for compact
storage.
NOTE: Do not store the cleaner in freezing conditions.
Do not store the cleaner with water in the tank. Do not store
the cleaner with cleaner cartridge attached. Turn the
squeegee upside down for storage. Squeegee will deform if
left in position while in storage.
Things To Do
• Use only manufacturer recommended attachments and accessories.
• Keep free of dust, lint, and hair.
• Turn off all controls before unplugging.
• Test the A.L.C.I. plug with every use.
• Empty the recovery tank when full and whenever clean water is
added to the supply tank.
• Keep young children and pets away from cleaned carpets until dry.
• Check carpets and upholstery for color fastness.
• Clean nozzle periodically.
To Replace Belt
WARNING: To reduce the risk of electric shock or injury from
moving parts, unplug before servicing.
Replacement belts (Part No. OR114) for Oreck Steemers are available
from Oreck. Call Toll-Free 1-800-989-3535.
fig. 4 Unplug the power cord leading from the power head to the rear
of the main cleaner.
fig. 3 Remove the power nozzle from the main cleaner.
fig. 21
Disassemble Power Nozzle:
a. Remove screw from belt cover.
b. Remove two (2) screws holding the brush roll clamp in place and
remove clamp.
c. Remove and replace the old belt if broken or if excessive wear is
noted.
To Install a New Belt:
d. Remove brush roll and insert the new belt into the rectangular
cavity. Using a long screwdriver, loop belt around motor shaft.
Pull and stretch belt over crowned end of the brush roll. Rotate
brush to properly align belt.
fig. 21 Replace belt cover, brush roll clamp and screws.
fig. 3 Reattach power nozzle to unit.
fig. 4 Reconnect power cords and test.
To Replace Squeegee
fig. 22 Remove squeegee by gently pulling the handles located on each
end of the squeegee until it releases.
a. Replace the squeegee by first inserting one tab on the squeegee
end with the slot on nozzle. Then insert the tab located on other
end of squeegee into the nozzle slot.
NOTE: Turn the squeegee upside down for storage. The
squeegee is designed to assist in hard floor cleaning,
however, it can be left on for carpet cleaning.