Filter
Top Products
11
Central Station Receiver 1 Format
From the table below, enter the central station's receiver format. Use number
buttons 1 through 9. NOTE: Press G0 for a zero and 0
for a blank space (•). Press G 1 through G 4 for letters B–E,
respectively. Press Jto save. Press NEXT (E) button to proceed.
NOTE: Central Station Receiver 2 and 3 Formats can only be entered in Direct
Address Programming. See CS Receiver Options.
Enter User Codes
For default program, enter up to 8 User Codes for Area 1 (Users 1 - 8) and up
to 8 User Codes for Area 2 (Users 9 - 16) . Press the (A) button once to
set the cursor to the User Number.
1 Enter the User Number to be programmed, including leading zeros. Use the number buttons 0 through 9 .
2 Enter a User Code of up to 6 digits. Use the number buttons 0 through 9 to enter the code followed by
G0 for each blank.
3 Enter the User Options. Refer to the User Option table below.
4 Enter the Authority Level. Refer to the Authority Level table below.
5 If this code is to be used to activate a door strike, assign the User to the appropriate access control keypad from the
Access Control Keypad table below.
Programming the GEM-P3200 & GEM-P9600
(Direct Entry)
05
INTERIOR
BYPASS FIRE/TBL SYS TBL CHIME
INTERIOR
BYPASS SYS TBL CHIME
FIRE/TBL
(Direct Entry)
06
INTERIOR
BYPASS FIRE/TBL SYS TBL CHIME
INTERIOR
BYPASS SYS TBL CHIME
FIRE/TBL
DATA
ENTRIES
AUTHORITY
LEVEL
COD E
TYPE
blank (•) NONE ARM/DISARM
1 LEVEL 1 ARM/DISARM
2 LEVEL 2 ARM/DISARM
3 LEVEL 3 ARM/DISARM
4 NONE ARM ONLY
5 LEVEL 1 ARM ONLY
6 LEVEL 2 ARM ONLY
7 LEVEL 3 ARM ONLY
8 NONE SERVICE
9 LEVEL 1 SERVICE
0 LEVEL 2 SERVICE
B LEVEL 3 SERVICE
USER OPTIONS
DATA
ENTRIES
BLOCKED
VIEW
USER
PROGRAM
BYPASS OVERVIEW
blank (•) DISABLED
1 Y
2 Y
3 Y Y
4 Y
5 Y Y
6 Y Y
7 Y Y Y
8 Y
9 Y Y
0 Y Y
B Y Y Y
C Y Y
D Y Y Y
E Y Y Y
F Y Y Y Y
ACCESS CONTROL KEYPADS
DATA
ENTRIES
K.P. 5 K.P. 6 K.P. 7
blank (•) NONE
1 Y
2 Y
3 Y Y
4 Y
5 Y Y
6 Y Y
7 Y Y Y
ACCESS CONTROL KEYPADS
DATA
ENTRIES
K.P. 1 K.P. 2 K.P. 3 K.P. 4
blank (•) NONE
1 Y
2 Y
3 Y Y
4 Y
5 Y Y
6 Y Y
7 Y Y Y
8 Y
9 Y Y
0 Y Y
B Y Y Y
C Y Y
D Y Y Y
E Y Y Y
F Y Y Y Y
User # User Code Option Level Access Control
When programming User Options, Authority Level and Access Keypads:
“A” = G 0 ; “B” = G 1 ; “C” = G 2 ;
“D” = G 3 ; “E” = G 4 ; “F” = G 5 .
CHANGING OR CANCELING A CODE: To change any code, merely program over the existing code as described above
and press Jto save. Similarly, to cancel a code, blank out each number of the code press Jto save.
DATA
ENTRY
CS RECEIVER 1 FORMAT
4 Radionics, DCI, Franklin Slow
5 Universal High Speed
8 Radionics BFSK
9 FBI 4/3/1
DATA
ENTRY
CS RECEIVER 1 FORMAT
0 Radionics Modem 2
B SIA
C Ademco Point ID
D Ademco Expres
E Pager
DATA
ENTRY
CS RECEIVER 1 FORMAT
•(blank) Ademco Slow, Silent Knight Slow
1 Sescoa, Vertex, DCI, Franklin Fast
2 Radionics Fast
3 Silent Knight Fast