Filter
Top Products
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards
(ANSI/NFPA 70-1996), including fire-rated construction.
Use this unit only in the manner intended by the manufacurer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding con-
ductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.
Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from
being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7
feet from the floor to the trailing edge of the blade.
WARNING – Risk of fire, electric shock, or personal injury, The fan in this box may be either directly supported from a structural fram-
ing member of a building and/or may be mounted to an outlet box marked acceptable for fan support of 31.80 kg. (70 lbs.) or less.
Most outlet boxes commonly used for the support of luminaires may not be acceptable for fan support and may need to be replaced.
Consult a qualified electrician if in doubt.
Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating
blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
NEVER place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heat-
ing equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA),
and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such
as a tag, to the service panel.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Installation
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS
SAFETY TIPS
TOOLS REQUIRED
Phillips Screwdriver Wire Cutters Pliers Step Ladder
Before you begin installing the fan,
Switch power off at Service panel and
lock service disconnecting means to
prevent power from being switched on
accidentally. When the service discon-
necting means cannot be locked,
securely fasten a prominent warning
device, such as a tag, to the service
panel.
Before installing this fan make sure the outlet box is
properly installed to the house structure or fan
brace/outlet box. WARNING – Risk of fire, electric
shock, or personal injury, The fan in this box may be
either directly supported from a structural framing
member of a building and/or may be mounted to an
outlet box marked acceptable for fan support. Most
outlet boxes commonly used for the support of lumi-
naires may not be acceptable for fan support and may
need to be replaced. Consult a qualified electrician if in
doubt. See Safety Tip # 8 above.
1
2
Loosen the 2 set screws on the yoke
to let the downrod slip into yoke.
Install downrod to yoke cover.
4 5
Thead leadwires and safety cable
through the downrod.
6
3
Outlet box
Wood
Screws
Mounting
Bracket
Secure mounting bracket directly to a
joist from the buliding structure via the
two knock out holes on the outlet box.
Use only the appropriate wood screws
and washers included with your fan.
Caution: Wood screws must go through
into the building joist.
BUILDING STRUCTURE METHOD
OUTLET BOX METHOD