Mitsubishi Electronics 30 Air Conditioner User Manual


  Open as PDF
of 12
 
4
ON/OFF
–
TIMER SETSET TEMP.
REMOTE CONTROLLER
MODE TIMER ON/OFF CLOCK/TIMER FAN SPEED AIR DISCHARGE FILTER
AIR SWEEP CHECK
TEST RUN
STAND BY
DEFROST
DRY COOL
AUTO FAN
HEAT
CENTRALLY CONTROLLED
˚F
SWING
FAN
SPEED
AUTO
RETURN
NOT AVAILABLE
˚F
CHECK MODE
FILTER
TIMER
TEST RUN
TIMER OFF CLOCKAUTO AUTO
CHECKSET TEMP. STARTSTOP
F
1
2. Operation
2.5. Adjusting airflow direction
The vertical air vane helps select the vertical direction of the airflow.
1 Press AIR DISCHARGE button to select the vertical airflow direction.
• Each time you press the button, the option changes are displayed on the remote
controller, as shown below.
A (swing) → B → C → D → E → A
• In cooling/drying mode with the fan speed set to LOW, every press on the button
will change the direction in the order of A, B, D, A. (C can not be set)
• If D or E is set, the angle will automatically revert to B after one hour of operation.
(Do not use D and E too often in cooling/drying mode with the fan speed set to
LOW, or condensation or dripping can occur.)
F “AUTO RETURN” should be displayed.
• When the angle setting is C in cooling mode, switching the fan speed from HIGH
to LOW will cause the angle to revert to B automatically.
• The airflow direction can not be set with UP/DOWN while the SWING setting is being used.
• The arrow indicators are alternately displayed when the air sweep is in operation,
however they are not displayed when the air sweep is not in operation.
• The left/right guide vanes of PC(H) series and the guide vane of the PK(H) serises
can be changed manually.
2.6. Using the timer
1) Set the current time
1 Press clock/timer button to display the “CLOCK” B.
Remote
CLOCK
→
AUTO
START
→
AUTO
STOP
→ No Display
controller display A
2 Each time you press
TIMER SET
button, the time increases in increments of one minute.
Each time you press
TIMER SET
button, the time decreases in increments of one minute.
• Press and hold the button to rapidly change the time.
• The time changes in increments of one minute → ten minutes → in units of hour; in
this order.
• Approximately ten seconds after pressing the button, the display on the remote
controller will turn off.
(For Wireless Remote Controller)
1 Press the CLOCK button using a thin stick and blink the time A.
2 Press the
h
and
min
button to set the current time.
3 Press the CLOCK button using a thin stick.
2) Set the time to start the unit as follows
1 Press clock/timer button to display B
AUTO
START
.
2 Press
TIMER SET
button to set the time that you want the unit to start.
The start time is displayed at A.
(For Wireless Remote Controller)
1 Press the
AUTO START
button.
• Time can be set while the following symbol is blinking.
ON time : B START is blinking.
2 Use the
h
and
min
buttons to set the desired time.
3 To cancel the ON timer, press the
AUTO START
button.
3) Set the time to stop the unit as follows
1 Press clock/timer button to display C
AUTO
STOP
.
2 Press
TIMER SET
button to set the time that you want the unit to stop.
The stop time is displayed at A.
(For Wireless Remote Controller)
1 Press the
AUTO STOP
button.
• Time can be set while the following symbol is blinking.
OFF time : C STOP is blinking.
2 Use the
h
and
min
buttons to set the desired time.
3 To cancel the OFF timer, press the
AUTO STOP
button.
4) Changing the set times
1 Press clock/timer button to display the time (CURRENT, START, STOP) you want
to change.
2 Press
TIMER SET
button to set the desired time.
• When change is made to either one of a pair, e.g., AUTO START or AUTO STOP,
set the time you need not to change to
. This display is available following
23:50.
(For Wireless Remote Controller)
Press the
AUTO START
or
AUTO STOP
to cancel the timer and repeat from 2) or 3).
↑
ABCDE
ABCDE
PL(H) Swing 30° 45° 55° 70°
PK(H)* Swing 10° 30° 60° 70°
PK12FK3 – 10° 30° 60° 70°
PC(H) Swing
100% Horizontal
20° 40° 60°
* Except PK12FK3
ON/OFF TEMP
FAN
VANE
TEST RUN
AUTO STOP
AUTO START
h
min
LOUVER
MODE
CHECK
RESETSET CLOCK
MODEL
SELECT
NOT AVAILABLE
SWING
CHECK
FAN
TEST
RUN
˚F
˚C
AMPMSTOP
START
AMPM
COOL
DRY
AUTO
FAN
HEAT
1
ON/OFF
–
TIMER SETSET TEMP.
REMOTE CONTROLLER
MODE TIMER ON/OFF CLOCK/TIMER FAN SPEED AIR DISCHARGE FILTER
AIR SWEEP CHECK
TEST RUN
STAND BY
DEFROST
DRY COOL
AUTO FAN
HEAT
CENTRALLY CONTROLLED
˚F
SWING
FAN
SPEED
AUTO
RETURN
NOT AVAILABLE
˚F
CHECK MODE
FILTER
TIMER
TEST RUN
TIMER OFF CLOCKAUTO AUTO
CHECKSET TEMP. STARTSTOP
B
1
2
A
ON/OFF TEMP
FAN
VANE
TEST RUN
AUTO STOP
AUTO START
h
min
LOUVER
MODE
CHECK
RESETSET CLOCK
MODEL
SELECT
NOT AVAILABLE
SWING
CHECK
FAN
TEST
RUN
˚F
˚C
AMPMSTOP
START
AMPM
COOL
DRY
AUTO
FAN
HEAT
A
2
13
ON/OFF
–
TIMER SETSET TEMP.
REMOTE CONTROLLER
MODE TIMER ON/OFF CLOCK/TIMER FAN SPEED AIR DISCHARGE FILTER
AIR SWEEP CHECK
TEST RUN
STAND BY
DEFROST
DRY COOL
AUTO FAN
HEAT
CENTRALLY CONTROLLED
˚F
SWING
FAN
SPEED
AUTO
RETURN
NOT AVAILABLE
˚F
CHECK MODE
FILTER
TIMER
TEST RUN
TIMER OFF CLOCKAUTO AUTO
CHECKSET TEMP. STARTSTOP
ABC
1
2
ON/OFF TEMP
FAN
VANE
TEST RUN
AUTO STOP
AUTO START
h
min
LOUVER
MODE
CHECK
RESETSET CLOCK
MODEL
SELECT
NOT AVAILABLE
SWING
CHECK
FAN
TEST
RUN
˚F
˚C
AMPMSTOP
START
AMPM
COOL
DRY
AUTO
FAN
HEAT
C
13
A
B
2
 previous next