Kenmore 70089 Air Conditioner User Manual


 
Controls
Figure 37. Touch Control Panel
aidm I I m B B
-)i 1 i I I }LOW Fo
/oFF "'°" s,vE.O.L*^ V"
COOL PLUS _ ____
MODE SET
EXHAUST CLOSEO
I
See Figure 37. Kenmore room air conditioners have an
electronic touch control panel located across top front of
unit. Functions and operation of each control are
explained below.
Touch Panel Controls
To operate touch controls, press control pad until
indicator above pad lights (does not apply to OFF or
V IA pads).
OFF--Turns air conditioner off.
SMART SET--Places air conditioner in "smart" cooling
mode. SMART SET uses computer logic to cool area
quickly and quietly.When unit first turns on, fan starts at
high speed. As room temperature nears set
temperature, fan automatically switches to medium
speed, then low speed. When room cools to set
temperature, fan continues to run at low speed and
compressor cycles on and off to maintain room
temperature.
LOW COOL--Fan operates continuously at low speed,
except in power saver mode. If unit is in a cooling mode,
compressor cycles on and off as required to maintain
set temperature. Select this setting for quietest
operation.
MED COOL--Fan operates continuously at medium
speed, except in power saver mode. If unit is in a
cooling mode, compressor cycles on and off as required
to maintain set temperature. Select this setting for
reduced air circulationand quieter operation.
HIGH COOL--Fan operates continuously at high speed,
except in power saver mode. If unit is in a cooling mode,
compressor cycles on and off as required to maintain
set temperature. Use this setting for maximum air
circulation and faster cool-down during initialstart up.
POWER SAVER PLUS--Places air conditioner in
energy-saving mode. Energy-saving mode works in
conjunction with SMART SET mode and low, medium,
or high fan speeds. In energy-saving mode, air
conditioner maintains room temperature within 1.5° F of
programmed temperature setting. When POWER
SAVER PLUS is selected, fan cycles on and off with
compressor, instead of running continuously as in other
modes. During compressor off cycle, fan automatically
turns on for about 2 minutes at 5 minute intervals to
sample room air temperature. If room temperature is
within 1.5°F of programmed temperature, time between
sampling increases to a maximum of 15 minutes.
If roomtemperature is more than 1,5°F above
programmed setting, fan continues to run and
compressor cycles on to cool room. When room cools
to set temperature, compressor and fan turn off and
time between air sampling cycles decreases to a
minimum of 5 minutes.
FAN ONLY--Fan operates continuously at set speed
(high, medium, or tow) and compressor remains off..
Use this setting to circulate air without cooling and, with
VENT CONTROL in EXHAUST position, to vent room
of stale air, odors, smoke, etc. Displays actual room
temperature.
V IA --Used to decrease ("down" arrow) or increase
("up"arrow) set temperature. When used with DELAY
START function, arrow keys adjust delay start or stop
time.
DELAY START--Allows programming a delay of up to
24 hours before air conditioner starts, or programming
air conditioner to automatically stop after up to 24 hours
ofoperation. Automatic start or stop is programmable
from 1 hour (minimum) up to 24 hours (maximum), in
one hour increments. See Operation Instructions for
information on programming air conditioner for delay
start or automatic stop.
Vent Control
Vent control lever, located on lower dght corner offront
panel, controls a damper that recirculates or exhausts
room air.
With control in CLOSED position, damper is closed and
air in area being cooled is recirculated through air
conditioner,filtered, cooled, and returned to room. No air
is exhausted (vented) outside.
NOTE: For maximum efficiency and cooling, vent
control should remain closed any time air
conditioner iscooling.
With controlin EXHAUST position, damper is open.
When open, room air is exhausted (vented) outside.
Usa exhaust position to remove stale or smoky air.
NOTE: To conserve energy, use FAN ONLY position
with EXHAUST feature.
Brightness Adjust Feature (some models)
Display brightness can be changed using V I A pad.
To decrease brightness, simultaneously press and hold
OFF pad with"down" arrow.To increase brightness,
press and holdOFF pad with =up"arrow key.