Filter
Top Products
5
Important Safeguards For All
Electrical Appliances
• Fully unwind the power cord before use.
• Connect only to a 230V or 240V power outlet.
• Do not let the power cord hang over the
edge of a bench or table, touch hot
surfaces or become knotted.
• To protect against electric shock, do not
immerse the power cord, power plug or
appliance in water or any other liquid or
allow moisture to come in contact with the
part, unless it is recommended in the
cleaning instructions.
• The appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
• Children should be supervised to ensure
that they do not play with the appliance.
• It is recommended to regularly inspect the
appliance. To avoid a hazard, do not use
the appliance if power cord, power plug or
appliance becomes damaged in any way.
Return the entire appliance to the nearest
authorized Kambrook Service Centre for
examination and/or repair.
• Any maintenance other than cleaning
should be performed at an authorised
Kambrook Service Centre.
• This appliance is for household use only.
Do not use this appliance for anything other
than its intended use. Do not use in moving
vehicles or boats. Do not use outdoors.
Misuse may cause injury.
• The installation of a residual current device
(safety switch) is recommended to provide
additional safety protection when using
electrical appliances. It is advisable that a
safety switch with a rated residual operating
current not exceeding 30mA be installed in
the electrical circuit supplying the appliance.
See your electrician for professional advice.
• Always turn the appliance to the ‘OFF’
position, switch off at the power outlet
and unplug at the power outlet when
the appliance is not in use.
• Before cleaning, always turn the appliance
to the ‘OFF’ position, switch off at the power
outlet, unplug at the power outlet and remove
the power cord, if detachable, from the
appliance and allow all parts to cool.
• Do not place this appliance on or near a heat
source, such as hot plate, oven or heaters
• Position the appliance at a minimum distance
of 20cm away from walls, curtains and other
heat or steam sensitive materials and provide
adequate space above and on all sides for
air circulation.
• To prevent a possible fire or heat damage,
allow ample space around the heater (at
1.7m at front and 0.5m at the rear, top and
sides) and do not totally or partially block the
air inlet or outlets in any manner. Check the
openings from time to time for accumulated
dust. Ensure long shag carpet does not
obstruct airflow under the unit.
• Do not touch hot surfaces.
• Switch OFF at the main On/Off switch and the
power outlet, then unplug and allow heater
to cool down before cleaning or storing.
• Do not use outdoors. This heater is not intended
for commercial use such as construction sites.
• Use this heater only as described in this
instruction manual. Any other use not
recommended by the manufacture may
cause fire electric shock or injury and voids
all warranties.
• Regularly inspect the supply cord, plug, control
settings, air inlets and outlets and main housing
for any damage, If found damaged in any
way, immediately cease use of the heater and
return to Kambrook or an authorized service
agent for inspection or repair.
• Keep the heater clean. Follow the cleaning
instructions provided in this book.
• Always ensure the heater is properly
assembled before use. Follow the
instructions provided in this book.
• Do not operate the heater on a sink
or drain board.
• Do not operate the heater on an incline
plane. Do not move while the heater is
switched on.
• To avoid an electrical overload, it is
recommended that no other appliances
are plugged into the same circuit as your
heater when it is in use.
NOTE: This Kambrook Ceramic
Tower Heater is electronically
controlled and will not operate
until the heater is plugged into
a 230V or 240V power point and
switched on.
KCE340_IB_A12.indd 5 2/11/12 11:37 AM