Filter
Top Products
PD30X-XPAGE 2 OF 8
OPERATING
AND SAFETY PRECAUTIONS
READ, UNDERSTAND, AND FOLLOW THIS INFORMATION TO AVOID INJURY AND PROPERTY DAMAGE.
EXCESSIVE AIR PRESSURE
STATICSPARK
HAZARDOUS MATERIALS
HAZARDOUS PRESSURE
WARNING
EXCESSIVE AIRPRESSURE. Can cause personĆ
al injury, pump damage or property damage.
S Do not exceedthe maximuminlet airpressureasstatedonthe
pump model plate.
S Besure materialhoses andother componentsareable towithĆ
stand fluid pressures developed by this pump. Check all
hoses for damage or wear. Be certain dispensing device is
clean and in proper working condition.
WARNING STATIC SPARK. Can cause explosion resulting
in severe injury or death. Ground pump and pumping system.
S Use the pump grounding screw terminal provided. Use Aro
PartNo. 66885-1 Ground Kitor connect a suitable ground wire
(12 ga. min.) to a good earth ground source.
S Secure pump, connections and all contact points to avoid
vibration and generation of contact or static spark.
S Consult local building codes and electrical codes for specific
grounding requirements.
S After grounding, periodically verify continuity of electrical
path to ground. Test with an ohmmeter from each component
(e.g., hoses, pump, clamps, container, spray gun, etc.) to
ground to insure continuity. Ohmmeter should show 100
ohms or less.
S Submerse the outlet hose end, dispensing valve or device in
the material being dispensed if possible. (Avoid free streamĆ
ing of material being dispensed.)
S Use hoses incorporating a static wire.
S Use proper ventilation.
S Keep inflammables away from heat, open flames and sparks.
S Keep containers closed when not in use.
WARNING Pump exhaust may contain contaminants. Can
cause severe injury. Pipe exhaust away from work area and
personnel.
S In the event of a diaphragm rupture material canbe forcedout
of the air exhaust muffler.
S Pipe theexhaust to a saferemote location whenpumping hazĆ
ardous or inflammable materials.
S Use a grounded 1" min. i.d. hose between the pump and the
muffler.
WARNING
HAZARDOUS PRESSURE. Can result inserious
injury or property damage. Do not service or clean pump,
hoses or dispensing valve while the system is pressurized.
S Disconnect air supply line and relieve pressure from the sysĆ
tem by opening dispensing valve or device and/or carefully
and slowly loosening and removing outlet hose or piping from
pump.
WARNING HAZARDOUS MATERIALS. Can cause serious
injury or property damage. Do not attempt to return a pumpto
the factory or service center that contains hazardous material.
Safe handling practices must comply with local and national
laws and safety code requirements.
S Obtain Material Safety Data Sheets on all materials from the
supplier for proper handling instructions.
WARNING EXPLOSION HAZARD. Models containing aluĆ
minum wetted parts cannot be used with III.-Trichloroethane,
Methylene Chloride or other Halogenated Hydrocarbon solĆ
vents which may react and explode.
S Check pump motor section, fluid caps, manifolds and all
wetted parts to assure compatibility before using with solĆ
vents of this type.
WARNING
MISAPPLICATION HAZARD. Do not use models
containing aluminum wetted parts with food products for huĆ
man consumption. Plated parts can contain trace amounts of
lead.
CAUTION Verify the chemical compatibility of the pump
wetted parts and the substance being pumped, flushed or reĆ
circulated. Chemical compatibility may change with temperaĆ
ture and concentration of the chemical(s) within the
substances being pumped, flushed or circulated. Consult the
material manufacturer and ARO Form No. 8677-P, Fluid ComĆ
patibility Guide, for information on chemical compatibility.
CAUTION
Maximum temperatures are based on mechaniĆ
cal stress only. Certain chemicals will significantly reduce
maximum safeoperating temperature. Consult FluidCompatiĆ
bility Guide forchemical compatibilityand temperature limits.
Refer to PUMP DATA on page 1 of this manual.
CAUTION Be certain all operators of this equipment have
been trained for safe working practices, understand it's limitaĆ
tions, and wear safety goggles/equipment when required.
CAUTION
Donot usethe pumpforthe structuralsupport of
the piping system. Be certain the system components are
properly supported to prevent stress on the pump parts.
S Suction and discharge connections should be flexible conĆ
nections (such as hose), not rigid piped, and should be comĆ
patible with the substance being pumped.
CAUTION Prevent unnecessary damage to the pump. Do
not allow pump to operate when out of material for long periĆ
ods of time.
S Disconnect air line from pump when system sits idle for long
periods of time.
CAUTION
Use only genuine ARO replacement parts to asĆ
sure compatible pressure rating and longest service life.
WARNING
CAUTION
NOTICE
= Hazards or unsafe practices which could
result in severe personal injury, death or
substantial property damage.
= Hazards or unsafe practices which could
result in minor personal injury, product or
property damage.
= Important installation, operation or
maintenance information.