Filter
Top Products
CCN 99713398
OPERATOR’S MANUAL PD05P-XXX-XXX
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
RELEASED: 5-15-98
REVISED:
11-12-10
(REV. J)
1/2" DIAPHRAGM PUMP
1:1 RATIO (METALLIC)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
Refer to Model Description Chart to match the pump mate-
rial options.
637140-XX for uid section repair (see page 4).
637141 for air section repair (see page 6).
PUMP DATA
Models . . . . . . . . . . . . . see Model Description Chart for “-XXX”
Pump Type . . . . . . . . . Air Operated Double Diaphragm
Material . . . . . . . . . . . . see Model Description Chart
Weight . . . . . PD05P-AAS-XXX . . . . . . . 8.36 lbs (3.79 kgs)
PD05P-ASS-XXX . . . . . . . . 14.6 lbs (6.62 kgs)
Maximum Air Inlet Pressure . . . . . . . . 100 p.s.i.g. (6.9 bar)
Maximum Material Inlet Pressure . . . 10 p.s.i.g. (0.69 bar)
Maximum Outlet Pressure . . . . . . . . . . 100 p.s.i.g. (6.9 bar)
Air Consumption @ 40 p.s.i. . . . . . . . 1 c.f.m. / gallon (approx.)
Maximum Flow Rate
( ooded inlet)
. . . 13 g.p.m. (49.2 l.p.m.)
Displacement / Cycle @ 100 p.s.i.g. . 0.040 gal. (0.15 lit.)
Maximum Particle Size . . . . . . . . . . . . . 3/32” dia. (2.4 mm)
Maximum Temperature Limits (diaphragm / ball / seat
material)
Nitrile . . . . . . . . . . . . . . . . . . . . 10° to 180° F (-12° to 82° C)
Polypropylene . . . . . . . . . . . . 35° to 175° F (2° to 79° C)
Santoprene® . . . . . . . . . . . . . . -40° to 225° F (-40° to 107° C)
PTFE. . . . . . . . . . . . . . . . . . . . . . . 40° to 225° F (4° to 107° C)
Viton® . . . . . . . . . . . . . . . . . . . . -40° to 350° F (-40° to 177° C)
Dimensional Data . . . . . . . . . . . . . . . . . . . see page 8
Noise Level @ 70 p.s.i., 60 c.p.m. . . . . . . 71.1 db(A)
c
c
The pump sound pressure levels published here have been updated to
an Equivalent Continuous Sound Level (L
Aeq
) to meet the intent of ANSI
S1.13-1971, CAGI-PNEUROP S5.1 using four microphone locations.
NOTICE: All possible options are shown in the chart, however, certain
combinations may not be recommended, consult a representative or
the factory if you have questions concerning availability.
MODEL DESCRIPTION CHART
PD05 P - A X S - X X X
Center Section Material
P - Polypropylene
Fluid Connection
A - 1/2 - 14 N.P.T.F. - 1
Ball Material
A - Santoprene
G - Nitrile
S - Stainless Steel
T - PTFE
V - Viton
Fluid Section Service Kit Selection
EXAMPLE: Model #PD05P-ASS-SAA
Fluid Section Service Kit # 637140-AA
PD05P - AXS - X X X
Ball Diaphragm
637140 - X X
Fluid Cap & Manifold Material
A - Aluminum
S - Stainless Steel
Diaphragm Material
A - Santoprene
G - Nitrile
T - PTFE / Santoprene
V - Viton
Seat Material
F - Aluminum
P - Polypropylene
S - Stainless Steel
Hardware Material
S - Stainless Steel
Figure 1
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET – BRYAN, OHIO 43506
(800) 495-0276 FAX(800) 892-6276
© 2010
www.ingersollrandproducts.com