Filter
Top Products
OPERATOR’S MANUAL
651616-X
RELEASED: 6-6-02
REVISED: 3-4-10
(REV. L)
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
TWO POST LIFT / RAM
For use with 5 - 55 Gallon Drums
(67081 BASIC LIFT / RAM PLUS FOLLOWER PLATE)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
INCLUDE MANUALS: 66516-X FOLLOWER PLATE (PN 97999-854), 67195-X FOLLOWER PLATE(PN 97999-841)&
S-635 GENERAL INFORMATION (PN 97999-635)
THIS MANUAL COVERS THE FOLLOWING MODELS (COMPLETE FOLLOWER DATA ON PAGE 3)
MODEL (See Page3 for Follower Plate)
TYPICAL PUMP APPLICATION
651616-1, -2, -3, -7, -8, -9, -13, -14, -15, -19, -51, -52, -53, -57, -58, -59, -63 3-1/4’’ TO 6’’ AIR MOTORS (TIE ROD PUMPS)
651616-4, -5, -6, -10, -11, -12, -16, -17, -18, -20, -54, -55, -56, -60, -61, -62, -64 8’’ TO 12’’ AIR MOTORS (TIE ROD PUMPS)
SERVICE KITS
116772 for repair of E512LM valve.
104302 for repair of R37121-100 miniature regulator.
GENERAL DESCRIPTION
TheARO Model651616-XTwo Post Lift/Ram usestwo3-1/2’’air-pow-
ered cylinders connected by tubular steel cross member and is welded
toaheavy gaugebaseplate.Itisnormally usedtoraiseandlower afluid
handlingpump andfollower in andoutof astandard 55-gallon drum,or
when usedas aram it canforce highviscosity flowablematerial i ntothe
pump inlet. It is offered with several follower plate options (see page 4)
which will accommodate most of the ARO Fluid Handling Industrial
pumps and allow connection directly to the pump lower end. There are
also mounting locations on the horizontal beam for the vertical rods al-
lowing use with 5 - gallon containers. Pump air controls (F-R-L) can be
mounted on the top horizontal support beam using the holes provided.
Cast aluminum followers are fitted with a dual lip seal or dual ‘‘O” ring
seal to wipe the drum clean and seal off the material from the atmo-
sphere. Severalmaterialoptions areavailable for thefollower plateout-
er seal. Select a compatible seal for the material being pumped. The
model chart above shows the pump motors they will generally accom-
modate.
Whenproperlysecured,thisunithasthe abilitytoraise apumptocleara
standard55-gallondrum.Theoperatoristhenabletoeasilyremovethe
pump from the drum.
This Lift/ Ramuses ahand lever 4-way controlvalve whichcontrols the
air necessary to raise and lower the lift. This unit includes an auxiliary
manualair valve whichisusedto supplyacontrolled amountofair pres-
sure to the bottom ofthe follower plate. When the control valve is in the
‘‘UP’’ position,asmall amountofair pressureapplied underthe follower
plate will help to raise the follower plate, pump and lift by relieving the
vacuum (refer to page 5).
Refer to page2for optionalaccessoriesavailable forpump stabilization
and drum hold down.
651616-1
TWOPOSTLIFT/RAM
BASE DIMENSIONS: 39-1/2’’ (1003.3 mm) x 24’’ (609.6 mm)
HEIGHT: LOWERED 61-17/32’’ (156.3 cm), RAISED: 99-5/32’’ (251.9 cm)
FIGURE 1
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET – BRYAN, OHIO 43506
(800) 495-0276 FAX(800) 892-6276
© 2010
www.ingersollrandproducts.com
CCN 99445348