Hotpoint HAG 51 K Burner User Manual


 
11
GB
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
Hotplate
The hotplate lid is fitted with a safety device which cuts
off the gas supply to the hotplate burners unless the lid
is fully open. Do not use the safety device as a means
of controlling the hotplate burners.
The hotplate has two high speed burners and two
simmering burners which will accommodate pans
between 100mm (4”) and 240mm (91/2”) diameter. All
pans should be positioned centrally over the burners.
TO USE THE HOTPLATE
1. Remove any items or spillage from the top of the
lid and then raise it to its fully open position.
2. Press the ignition button and then push in and
turn the control knob of the chosen burner anti-
clockwise to the large flame symbol. Continue to
press the ignition button until the sparks light the
gas.
3. Turn the control knob anti-clockwise to reduce the
heat input. Only turn the control knob between the
large flame symbol and the small flame symbol
when adjusting the setting.
4. To turn off, turn the control knob fully clockwise to
the symbol O.
DO NOT use the hotplate unless all pan supports
are in position.
DO NOT use mis-shapen pans which may be un-
stable.
DO NOT use round base woks directly on the pan
supports.
DO NOT use the glass lid as a working surface.
Each burner is fitted with a spark ignitor for lighting the
gas. To ensure rapid lighting of the burners every time
they are used, the ignitors must be kept clean and dry.
Remove any food spillage or cleaning materials from
the ignitor using a small nylon brush such as a tooth
brush. Access to the ignitor can be achieved by lifting
off the loose burner parts carefully when the burners
are cool.
When the hotplate burner bodies and caps are
removed for cleaning, be careful not to drop any food
particles or cleaning materials into the burner bases, to
avoid the possibility of blocking the gas jets.
If aluminium based pans are used, a silvery deposit
may appear on the top edge of the pan support
fingers. See ‚Care and Cleaning’ section for cleaning
information.
SAFETY REQUIREMENTS FOR DEEP FAT FRYING
1. Never fill chip pans more than one third full with oil
or fat.
2. Never leave oil or fat unattended during the heating
or cooling period.
3. Never heat fat or fry with a lid on the pan.
4. Always dry food thoroughly before frying, and lo-
wer it slowly into the hot oil or fat. Frozen foods in
particular will cause frothing and spitting if added
too quickly.
5. Always keep the outside of the pan clean and free
from streaks of oil or fat.
HOW TO DEAL WITH A FAT FIRE
1. Do not move the pan.
2. Turn off the hotplate burners.
3. Smother the flames with a fire blanket or damp
cloth to extinguish the fire. Do not use water or a
fire extinguisher as the force of it may spread the
burning fat or oil over the edge of the pan.
4. Leave the pan for at least 60 minutes before moving
it.
Models with Hob Gas Burner Safety Devices to
Prevent Leaks
These models can be identified by the presence of the
device itself.
! Since the hob burners are equipped with a safety
device, you must hold the control knob in for about 3-7
seconds after the burner has been lighted to allow the
gas to pass until the safety thermocouple has heated.
Practical Advice on Using
the Burners
To use the burners as
efficiently as possible, some basic guidelines should
be followed:
Use cookware that is the right size for each burner
(see table) in order to prevent the flame from
spreading beyond the bottom of the cookware.
Only use cookware with flat bottoms.
As soon as the boiling point is reached, turn the
knob to the lowest setting.
Always use lids with pots and pans.
HOB GAS BURNER
SAFETY DEVICE
ELECTRONIC
LIGHTING DEVICE
Burner ř Cookware diameter (cm)
Fast (R) 20 -22
Semi Fast (S) 16 - 20
Auxiliary (A) 10 - 14