Filter
Top Products
LYNXR-I Installation and Setup Guide
- 32 -
✻
56 Enhanced Zone Programming Mode
IA LC
Enroll mode
0 = advance to the VOICE DESCRIPTOR
prompt (1C).
Note: This will save all zone parameters.
1 = enter now and proceed to SERIAL
NUMBER prompt (1b).
Note: Not applicable if the serial number is already
present.
2 = copy the last serial number entered into
local ram.
Note: If this is the 1st zone, none will be in the buffer
and the panel will emit a long tone. Not valid if
serial number is already present.
3 = view existing serial number.
Note: Only if “L” is displayed. If “L” is not displayed,
panel will emit a long beep.
9 = advance to F; delete existing serial
number.
Note: Only if “L” is displayed. If “L” is not displayed,
panel will emit a long beep.
[✻] = advance to the VOICE DESCRIPTOR
prompt (1C). This will save all zone
parameters.
[#] = return to the LOOP NUMBER prompt (E).
Note: In order for all entered parameters to be
accepted, you must advance to the VOICE
DESCRIPTOR prompt (1C).
If “L” is displayed, the serial number for this transmitter has already
been entered. It may, however, still be viewed, confirmed (only if in
listen mode), or deleted.
View serial number
Enter “3”. Each digit will be redisplayed, and the keypad will beep once
for digits 1-6, and three times for the last digit.
Confirm serial number
The serial number/loop number combination can be confirmed after one
transmission from a BR type device or two transmissions (fault and
restore) from a UR or RF type device. If a transmission is received that
matches the serial number and loop number entered, the system will
confirm the reception by announcing the Voice Descriptor for the zone,
if it is programmed, followed by three beeps, and a “C” will appear on
the display indicating the received serial number and loop number
have been confirmed. No further transmissions will be received.
Delete serial number
The serial number can be deleted by entering “9”.
If “L” is not displayed, the serial number for this transmitter has not
been previously entered. You may enter the serial number manually,
copy the previous serial number, return to Prompt (E) or enter the
serial number later using the
✻83 Enhanced Sequential Mode.
Manual entry
Enter "1" to advance to Serial number prompt (1b).
Copy the previous serial number
Enter “2” to copy the previous serial number entered.
Return to Prompt (E)
Enter “#” to return to Loop Number prompt (E).
Enter transmitter later
Enter “0” or “
✻” if you wish to enter the transmitter later, using the
✻83 Enhanced Sequential Mode described later in this manual.
Notes: (1) The panel will listen only when it is in the idle loop waiting
for key entry and a serial number has been entered. If a key
is entered, the function must be completed and the panel
will listen again.
(2) A long beep indicates illegal entry or duplicate serial number/loop
entry
Ib
Serial number
Enter the transmitter’s 7-digit serial number.
[#] = return to prompt 1A and reject any serial
numbers entries that have been made.
[✻] = return to prompt 1A, (if a valid serial
number has been entered, the "L" is
displayed and the serial number will be
copied into EEROM from the last serial
entered into the buffer.)
Note: This prompt can be used only to manually
enroll a serial number. RF enrollment will be
rejected and the current zone descriptor will be
announced, followed by a single long beep
and the system will return to prompt (1A).
In this mode, the transmitter serial numbers can only be entered
manually.
Enter the 7-digit serial number printed on the transmitter. If an
incorrect digit is entered, press the [#] key to backup to prompt (1A)
and start over. When all 7 digits are entered, press the [
✻] key.
If 52 seconds passes and no entry has been made, the system returns
to prompt (1A).
Notes: (1) If the serial and loop number combination is already
present the keypad will emit a single long beep and the
system will return to the (1A) prompt and “L” will be
displayed.
(2) If less than 7 digits have been entered, the keypad will
emit a single long beep and return to the (1A) prompt
without displaying the “L”.
(3) If more than 7 digits have been entered, the first 6 digits
will be saved along with the last digit that was entered
(entering 123456789 yields the serial number 1234569).
IC
Voice descriptor
0 = skip to next zone (A)
1 = enter descriptor mode; existing descriptor
for this zone will be announced
Each zone can have a voice descriptor of up to 3 words that will be
announced whenever the system announces status for that zone.