Filter
Top Products
OPERATING INSTRUCTIONS
MESURES DE PRÉCAUTION
Changing the Headlight Bulb
WARNING: To reduce the risk of
electric shock, the power cord
must be disconnected before removing
the dust cup, HEPA filter,changing the
filters or performing maintenance/trouble
shooting checks.
IMPORTANT: Si la trappe de succion ou le boyau se BLOQUENT, éteignez
l’aspirateur et retirez l’obstacle avant de redémarrer l’appareil.
Notches
Fig. 29
4. Tenez toutes les parties du corps,
les doigts, les cheveux et les
vêtements lâches éloignés des
ouvertures, du batteur rotatif et des
autres pièces mobiles.
2. Avant d’insérer la fiche d’alimentation
dans la prise murale, assurez-vous
que vos mains sont sèches.
1. N’approchez pas l’aspirateur
trop près des éléments
chauffants ou des radiateurs.
1. Turn unit “Off” and unplug from wall
outlet.
2. With a flat head screw driver, snap off
the lens cover by pressing down on the
two notches on the lens cover. (Fig. 29)
3. Lift off the head light lens.
4. Remove the light bulb by pulling it out
carefully.
5. Lorsque vous retirez le cordon
d’alimentation de la prise
murale, tirez sur la fiche et non
pas sur le cordon.
5. Replace the new bulb by pushing
it in.
6. Replace the head light lens by
pushing it in so that it snaps back in
place.
PROBLEM SOLVING
This appliance was inspected thoroughly and was in good operating condition when it
was shipped from the factory. If a minor problem occurs, it usually can be solved quite
easily when the cause is found. Therefore, this checklist is provided for your
convenience.
PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTIONS
Cleaner Won’t
Run
1. Not properly plugged into
wall outlet.
2. No electricity in wall outlet.
3. On/Off switch not turned on.
4. Motor thermostat tripped.
5. Blown fuse/tripped breaker.
1. Plug in firmly.
2. Check fuse or breaker.
3. Push on/off switch to on
4. Reset motor thermostat.
5. Reset circuit breaker or replace fuse.
Cleaner Won't
Pick Up
1. Full or clogged dust cup.
2. Wrong pile height setting.
3. Clogged nozzle.
4. Clogged dust inlet port.
5. Clogged hose.
6. Broken belt.
7. Hose not inserted fully.
8. Dirty filters.
9. HEPA filter needs cleaning
or replacing.
10. HEPA filter frame needs
cleaning.
11. Blockage in unit.
1. Clean dust cup.
2. Adjust setting.
3. Remove obstruction.
4. Remove power head cover and
remove obstruction.
5. Remove obstruction.
6. Replace belt.
7. Push hose in securely.
8. Clean / change filters.
9. Clean or replace HEPA filter.
10. Clean HEPA filter frame.
11. Check unit for blockages.
Cleaner Picks
Up Moveable
Rugs Or Pushes
Too Hard
1. Wrong pile height setting. 1. Adjust setting.
Agitator Does
Not Turn
1. Broken belt.
2. Belt installed incorrectly.
1. Replace belt.
2. Check belt changing and agitator
cleaning.
Air Flow
Restricted With
Attachment Use
1. Attachment use restricts air
flow.
2. New carpet debris clogging
air path.
1. Check attachment.
2. Remove obstruction.
6. Ne ramassez aucun objet fumant
ou brûlant tels que les cigarettes,
allumettes ou cendres chaudes.
3. Avant de commencer à nettoyer,
assurez-vous de retirer tout gros objet
ou tout objet coupant pouvant l’écran
de filtrage de la coupelle.
7. Évitez de faire passer l’aspirateur
sur le cordon d’alimentation.
8. N’utilisez pas l’aspirateur sans
sa coupelle ou tous ses filtres.
10 27