Filter
Top Products
Convertible Brush
OPERATING INSTRUCTIONS
Using The Accessories For Dry
Vacuuming
Cyclonic Attachment
The cyclonic attachment is for dry
vacuuming only. This attachment
captures dust and dirt particles. You
must use at least one extension tube
with the cyclonic filter tube, along with
the desired accessory.
Crevice Tool
For hard to reach areas use
crevice tool with cyclonic dirt
tube and extension tube or
directly onto flexible hose.
Fig. 5
4
For vacuuming high, hard to reach
places such as ceilings,
curtains/drapes, etc., use the
convertible brush with removable
bristles as follows:
1. Insert the convertible brush to the
hose alone or with the extension
tube attached to the hose.
2. If you need a brush action, slide on
the removable bristle brush onto the
deluxe brush. (Fig. 4)
Fig. 4
Floor Brush
NOTE: The floor brush is only intended
for dry vacuuming. Use with the
cyclonic attachment or directly on the
hose with extension tubes in place.
• The bristles under the floor brush
can be left in the “Down” position for
use on carpets or can be
lifted to the “Up” position
for vacuuming floors.
(Fig. 5)
Turbine
Tilt
Upwards
Locking Latch
Air Driven Turbo Brush
IMPORTANT: Do not use the Air
Driven Turbo Brush for wet pick-up.
The air driven turbo brush removes
embedded dust and pet hair. The
efficiency of your air driven turbo brush
depends on the bristle brush rotating at
high speed. Strong air suction is needed
to accomplish this. In order to ensure that
maximum air suction is maintained,
please read the following instructions:
1. Empty the water tank and cyclonic
dust cup frequently.
2. Ensure that the rotating brush is kept
free of hair and string which may
accumulate and decrease brush
performance.
3. Keep air driven turbo brush turbine
free of dirt and foreign matter. (See
illustration for cleaning instructions.)
From time to time, the turbine of your
turbo brush will require cleaning. To do
this:
1. Remove the turbo brush from the
hose or extension tube.
2. Slide locking latch forward then tilt the
top housing of the brush upwards.
The top housing is hinged and will tilt
up approximately 45° only.
3. There may be some dust, lint, hair,
etc on the turbine wheel. Remove as
much of this as possible.
4. You may also use the unit’s hose with
crevice tool attached and use the
vacuum to remove any additional
debris from the turbine.
5. Ensure that the turbine wheel moves
freely by rotating it with your finger. If
the turbine does not rotate, call
1 (800) 798-7398 for help.
6. Once clean, close the top cover of the
turbo brush and slide the locking latch
toward the rear of the brush to lock.
Cleaning Air Driven Turbo Brush
OPERATING INSTRUCTIONS
5
Hints for Spot Cleaning Carpets
Note: Before spot cleaning your carpet
with the triangular brush, test for color
fastness. Dampen a white cloth with the
cleaning solution that you wil
l be using and
test a small area in a closet or under a
piece of furniture. Gently rub the cloth over
the area. Check each color for bleeding. If
the cloth remains white, it should be safe to
clean the carpet or upholstery. When using
commercial pre-cleaners spot removers,
follow manufacturers instructions and
follow this procedure with vacuum.
1. Apply the pre-cleaner spot remover to
the carpet as per manufacturers
instructions.
2. Using the triangular water brush, suck
the pre-cleaner spot remover liquid
from the carpet.
3. Spray the same area with water.
4. Vacuum again to remove the water.
5. Repeat steps 3 and 4 again if
necessary.
6. Empty the water tank.
Accessories for Use With the Wet
Pick-Up:
• Small Squeegee
• Large Squeegee
• Triangular Water Brush
Using the Accessories for Wet
Vacuuming
NOTE: Never use the Cyclonic
Attachment when using the vacuum
for wet pick-up.
Using Your Water Filtration
Vacuum for Wet Pick-Up
WARNING: When using your vacuum
for wet vacuuming empty water tank
and remove cyclonic attachment before
vacuuming. DO NOT use vacuum with
cyclonic attachment when using
vacuum for wet pick-up.
WARNING: Water level MUST NEVER
exceed the "Max" level indicated on the
water tank. Empty tank when water level
reaches "
MAX" indicator. If water is seen to
be coming from the exhaust - immediately
turn the unit off and unplug from electrical
outlet. Empty water tank and clean.
IMPORTANT: This unit is supplied with a
safety feature that will stop air flow if the
tank is overfilled. If the airflow is stopped,
shut off vacuum, empty tank, reassemble
vacuum and continue.
9. If there is a large volume of liquid to
be picked up, empty tank regularly.
DO NOT allow tank to overfill.
10.If water is escaping from the exhaust
shut off unit immediately and empty
the tank before resuming.
Fig. 6
Large Floor Squeegee
The large floor squeegee
is excellent for small spills
on floor surfaces. Can
be used directly onto flexible hose or
with extension tube.
Small Floor Squeegee
The small squeegee is good
for small tight areas.
Triangular Water Brush
The triangular water brush
is best for spot cleaning
on carpets.
1. Add 3 cups, (24 oz) of water to the
tank.
2. Insert plug into electrical outlet.
3. To connect the flexible hose into the air
intake duct, align the arrow on the
hose with the arrow on the unit. Push
in and turn 90° clockwise to lock the
hose in place. (See Fig. 1 on Page 3)
4. Attach the flexible hose to the canister.
(See Fig. 1 on page 3)
5. Push extension tube into the cyclonic
air intake opening and attach desired
accessory to the other end. (See Fig. 1
on page 3)
6. Turn the "On/Off" Switch to the "On"
position.
7. The flexible hose is equipped with
a manual suction control to adjust
the amount of suction required. For
strong suction ensure that suction
button is closed. To decrease
amount of suction slide the button
to open until desired strength is
obtained. (See Fig. 3 on page 3)
8. Select and attach accessory to the
other end of flexible
hose. If an extended
reach is desired
attach one or
more
extension
tubes directly
to flexible
hose. (Fig. 6)