Filter
Top Products
107172
16
For more information, visit www.desatech.com
For more information, visit www.desatech.com
7. With control knob pressed in, press and release ignitor but-
ton. This will light pilot. The pilot is attached to the front
burner. If needed, keep pressing ignitor button until pilot lights.
Note:
If pilot does not stay lit, contact a qualified service
person or gas supplier for repairs. Until repairs are made,
light pilot with match. To light pilot with match, see Manual
Lighting Procedure.
8. Keep control knob pressed in for 30 seconds after lighting
pilot. After 30 seconds, release control knob.
• If control knob does not pop out when released, contact
a qualified service person or gas supplier for repairs.
Note:
If pilot goes out, repeat steps 4 through 8.
9. Slightly push in and turn control knob counterclockwise
to the ON position.
10. Wait one minute and switch selector switch to the ON posi-
tion to light burners.
11. Set flame adjustment knob to any level between HI and LO.
OPERATING FIREPLACE
Continued
OPERATING FIREPLACE
Lighting Instructions (Cont.)
To Turn Off Gas To Appliance
Manual Lighting Procedure
Optional Remote Operation
WARNING: Make sure the selector switch is in the
OFF position when you are away from home for long
periods of time. Heater will come on automatically with
selector switch in the ON position.
1. Follow steps 1 through 6 under Lighting Instructions, page 15.
2. Depress control knob and light pilot with match.
3. Keep control knob pressed in for 30 seconds after lighting
pilot. After 30 seconds, release control knob. Now follow
steps 9 through 11, column 1.
Shutting Off Heater
1. Turn control knob clockwise to the OFF position.
2a. Set selector switch in the OFF position.
2b. If Using Optional Hand-Held Remote: Set selector switch in
the OFF position to keep from draining battery.
Shutting Off Burners Only (pilot stays lit)
You may shut off the burners and keep the pilot lit by doing one
of the following:
• Turn control knob clockwise to the PILOT position.
• Use remote control manual OFF button.
• Set selector switch in the OFF position.
Figure 31 - Pilot (Propane/LP)
Ignitor
Electrode
Pilot Burner
Figure 30 - Pilot (Natural)
Pilot Burner
Ignitor
Electrode
TO TURN OFF GAS TO APPLIANCE
MANUAL LIGHTING PROCEDURE
1. After lighting, let pilot flame burn for about one minute.
Turn control knob to ON position. Adjust flame adjust-
ment knob anywhere between HI and LO. Slide the selec-
tor switch to the REMOTE position (see Figure 32, page
17).
Note:
The burners may light if hand-held remote ON
button was on when selector switch was last turned off.
You can now turn the burners on and off with the hand-
held remote control unit.
IMPORTANT
: Do not leave the selector switch in the RE-
MOTE position when the pilot is not lit. This will drain the
battery.
IMPORTANT:
Be sure to press the ON/OFF buttons on the
hand-held remote control unit for up to 3 seconds to assure
proper operation.
GHRC Series Operation:
2a. Press the ON/OFF button to turn the burners on and off.
When turning burners off, the pilot will remain lit.
NOTICE: You must light the pilot before using the
hand-held remote control unit. See
Lighting Instruc-
tions
on page 15.
OPTIONAL REMOTE OPERATION
Note:
All remote control accessories must be purchased sepa-
rately (see Accessories, pages 28 through 30). Follow instruc-
tions included with the remote control.
Thermostat Control Operation
(Optional GHRCTA Series Only) The thermostat control set-
ting on the remote control unit can be set to any comfort level
between WARMER and COOLER. The burners will turn on
and off automatically to maintain the comfort level you select.
The ideal comfort setting will vary by household depending
upon the amount of space to be heated, the output of the central
heating system, etc.
For wall thermostat operation, follow instruction supplied with
thermostat accessory GWMT1. For wall switch operation fol-
low instructions supplied with GWMS2.