Desa (V)K42N Indoor Fireplace User Manual


 
www.desatech.com
111921-01E 23

The hand-held remote can be operated using either the manual
mode (MANU) or thermostatic mode (AUTO) (see Figure 52).
To select Fahrenheit/Centigrade mode display, carefully press
the ˚C/˚F mode button with the end of a paper clip or similar
blunt object.
Figure 52 - Thermostat Hand-Held Remote Control Unit
HRC200
LOCK
MANU AUTO
ºC/ºF
TEMP
POWER
ROOM
TEMP
SET
TEMP
AUTO
Turns Hand-Held
Remote On or Off
and Allows You to
Choose the Manual
Setting
Selects
AUTO Mode
°C/°F Mode Button
Locks System to
Prevent Accidental
Ignition
Turns Burners
On or Off
Increases or
Decreases Room
Temperature in
AUTO Mode
Digital Display Shows
Temperature and Settings
Manual Mode
1. Press the POWER and LOCK buttons together to turn on
the hand-held remote control.
2. Press the MANU button to turn on the replace.
3. Press the POWER and LOCK buttons together to turn off
the replace.
Auto (Thermostatic) Mode
1. Press the POWER and LOCK buttons together to turn on
the hand-held remote control.
2. Press AUTO button to select this mode.
3. Set the desired room temperature by pressing the TEMP
+ or - buttons.
4. Press the POWER and LOCK buttons together to turn off
the replace
Note: Do not leave the hand-held remote in the AUTO mode
close to the replace. The radiant heat from the replace will
turn off the replace. Ideally, place the hand-held remote in the
center of the room facing towards the replace.
Note: Do not hold the hand-held remote for a long time. Body
temperature will affect its operation in the AUTO mode.
Safety Features
When away from home for an extended period of time or as
a child safety feature to prevent accidental ignition of the re-
place, the receiver ON/OFF/REMOTE switch should be in the
OFF position.
Auto Shutoff Feature
1. If the average room temperature exceeds 82° F (28° C), the
hand-held remote control will perform a safety override
and shut the replace off. This feature is not available in
the MANU mode.
2. The receiver continuously receives signals from the hand-
held remote to control the room temperature. If the hand-
held remote is misplaced, obstructed or for any reason
cannot transmit to the receiver, the receiver will shut off
the replace after 8 minutes.

This feature allows the user to lock/unlock the keypad on the
hand-held remote in the MANU or AUTO mode to prevent
inadvertent operation (i.e. children operating the hand-held
remote control, etc.). The keypad is locked in either on or off.
Press the POWER and LOCK buttons together to turn the
unit on or off.
OPERATING OPTIONAL GWMT1
WALL MOUNTED THERMOSTAT
WARNING: Do not connect the thermostat to a
       
will occur.
Light the replace as instructed in Lighting Instructions on page
21. Set wall thermostat to desired temperature.
This thermostat has been electronically calibrated at the factory
and requires no adjustment or leveling.
Upon installation, the thermostat must be allowed to stabilize
at room temperature for a minimum of 30 minutes for proper
operation.
To turn the replace off, adjust thermostat to the lowest setting
and turn the gas control knob back to PILOT. The pilot will
remain lit.
IMPORTANT: To turn the pilot off, turn the gas control knob
on the heater to the OFF position.
OPERATING OPTIONAL

Locate the blower controls by opening the lower louver panel
on the replace. Blower controls are located on the right side of
the switch bracket to the left just inside the louver panel.
The BK manual blower and the BKT thermostatically-controlled
blower have an ON setting and an OFF setting. The blower
will only run when the switch is in the ON position. In the OFF
position, the blower will not operate.
Note for BKT Only: If you are using BKT blower with optional
thermostat (wall mounted or remote control) for the replace,
your replace and blower will not turn on and off at the same
time. The replace may run for several minutes before the blower
turns on. After the heater modulates to the pilot position, the
blower will continue to run. The blower will shut off after the
rebox temperature decreases.
The blower helps distribute heated air from the replace. Peri-
odically check the louvers of the rebox and remove any dust,
dirt or other obstructions that will hinder the ow of air.
OPERATING FIREPLACE
Continued