Desa NZ119 Electric Heater User Manual


 
www.desatech.com
118621-01B18
To Activate the Program Mode
A short push (press and release) on TIME/
PROGRAM button will activate or deactivate
program mode.
A long push (press and hold for more than
5 seconds) on TIME/PROGRAM button will
enter into setting of program.
When the program mode is activated, the P-1
and P-2 icons and the word OFF will display
on the screen. This means that unit turns off
manual mode and enters into program mode.
The unit will automatically check if current time
is within pre-programmed ON time.
If current time is within program on time, unit
will enter into thermo mode automatically
and the word THERMO and set temperature
digit(s) will display on screen.
When room temperature is below set tem-
perature, unit will turn on and the word ON
will replace the word OFF on the screen. The
ame icon will also show on the screen. Unit
will continue to operate in thermo mode until
program off time is reached. When program
off time is reached, unit will turn off and stay
off until next program on time is reached or
until user turns program mode off and turns
unit on in manual or thermo mode.
If current time is not within program on time,
unit will stay off until pre-programmed turn
on time is reached. Pre-programmed time
(P-1 and P-2 icons) will continue to display
on screen indicating that unit is in program
mode until set time is reached.
When program mode is deactivated, P-1 and
P-2 icons and set temperature digit(s) will
disappear from screen.
Factory Settings
The program function is preset at the follow-
ing on and off times. These times will apply
to every day of the week.
Program 1 (P1): Turn on at 7:00 AM. Turn off
at 9:00 AM.
Program 2 (P2): Turn on at 5:00 PM. Turn off
at 8:00 PM.
Setting a New Program
To change Program from the factory settings
to new settings:
1. Press and hold TIME/PROGRAM button
for more than 5 seconds to enter Set
Program Mode.
OPERATING HEATER
Continued
2. P1 ON will ash. Push UP or DOWN but-
ton until desired on time for Program 1 is
reached. Press SET button.
3. P1 OFF will ash. Push UP or DOWN
button until desired off time for Program
1 is reached. Press SET button.
4. P2 ON will ash. Push UP or DOWN but-
ton until desired on time for Program 2 is
reached. Press SET button.
5. P2 OFF will ash. Push UP or DOWN
button until desired off time for Program
2 is reached. Press SET button.
The new program is now set and unit is in pro-
gram mode. To take unit out of program mode,
press and release TIME/PROGRAM button.
Note: In set program mode, set times will ash
for 15 seconds. If the UP, DOWN or SET but-
ton is not pressed within 15 seconds, system
will automatically complete set up process and
LCD Screen will revert to normal readouts.
The rst factory set temperature is at 45° F.
Appliance will not turn on if room is not below
the set temperature. If set temperature is at
70° F, appliance will come on only if room
temperature is below 70° F.
Low Battery Indicator
A low BATTERY ICON on left side of LCD
screen will appear when battery power has
dropped signicantly. At this time, approxi-
mately two weeks of battery power remains
until remote control may experience partial or
complete loss of functions.
Childproof “Lock Out” – (CP)
This remote control includes a childproof lock
out feature that allows the user to “lock out”
operation of appliance from remote control.
1. To activate lock out feature, press and
hold UP and TIME/PROGRAM buttons
together for 5 seconds. Letters CP will
appear in room temp window frame on
LCD screen.
2. T
o disengage lock out, press and hold UP
and TIME/PROGRAM buttons together for 5
seconds or more. Letters CP will disappear
from LCD screen and remote control will
return to its normal operating condition.
Note: If appliance is already operating in on or
thermo modes engaging lock out will not cancel
the operating mode. Engaging lock out only
prevents manual operation of remote control.
If in auto modes, the thermo operation will
continue to operate normally. To totally lock out
operation of remote control’s operating signals,
remote control’s mode must be set to off.