Filter
Top Products
7
103413
OWNER’S MANUAL
INSTALLATION
Continued
IMPORTANT:
Vent-free heaters add mois-
ture to the air. Although this is beneficial,
installing fireplace in rooms without enough
ventilation air may cause mildew to form
from too much moisture. See Air for Com-
bustion and Ventilation, pages 4 through 6.
IMPORTANT:
Make sure the fireplace is
level. If fireplace is not level, log set will not
work properly.
NOTICE: A qualified service per-
son must install fireplace. Follow
all local codes.
WARNING: Never install the
fireplace
• in a bedroom or bathroom
• in a recreational vehicle
• where curtains, furniture,
clothing, or other flammable
objects are less than 42 inches
from the front, top, or sides of
the fireplace
• in high traffic areas
• in windy or drafty areas
CAUTION: This fireplace cre-
ates warm air currents. These cur-
rents move heat to wall surfaces
next to fireplace. Installing fire-
place next to vinyl or cloth wall
coverings or operating fireplace
where impurities (such as to-
bacco smoke, aromatic candles,
cleaning fluids, oil or kerosene
lamps, etc.) in the air exist, may
discolor walls.
Note:
Your Comfort Glow fireplace is de-
signed to be used in zero clearance installa-
tions. Wall or framing material can be placed
directly against any exterior surface on the
rear, sides, or top of your fireplace, except
where stand-off spacers are integrally at-
tached. If stand-off spacers are attached to
your fireplace, these spacers can be placed
directly against wall or framing materials.
Use the dimensions shown for rough open-
ings to create the easiest installation (see
Built-In Fireplace Installation, page 13).
CHECK GAS TYPE
Use only natural gas. If your gas supply is
not natural gas, do not install fireplace. Call
dealer where you bought fireplace for proper
type fireplace.
ELECTRICAL HOOKUP
(When Using Optional
Blower)
The optional blower accessories (GA3650T
and GA3750) have a power cord 5 feet in
length. You must locate the fireplace within
reach of a 120 volt grounded electrical out-
let, or install an electrical outlet within reach
of the blower power cord. For built-in in-
stallation, an outlet accessory (GA3555) is
available (see Accessories, page 25). This
allows the outlet to be installed inside the
firebox. All electrical installations should
be performed by a qualified service person.
ASSEMBLING AND
ATTACHING OPTIONAL
BRASS TRIM ACCESSORY
(Included with Mantel)
Note:
The instructions below show assem-
bling and attaching brass trim to fireplace.
Do not yet install trim if performing a built-
in installation (see Built-In Fireplace In-
stallation, page 13).
1. Remove packaging from three pieces
of brass trim.
2. Locate four brass screws, two adjust-
ing plates with set screws, and two
shims in the hardware packet.
3. Align shim under adjusting plate as
shown in Figure 5.
4. Slide one end of adjusting plate/shim
in slot on mitered edge of top brass trim
(see Figure 5).
Figure 5 - Assembling Brass Trim
Figure 6 - Attaching Brass Trim to
Fireplace
Side Brass
Trim
Top Brass
Trim
Slot
Mitered
Edge
Slot
Shim
Set Screws
Adjusting
Plate
Trim Hanging
Screws
Assembled
Brass Trim
Hanging Notches
on Trim
5. Slide other end of adjusting plate/shim
in slot on mitered edge of side brass
trim (see Figure 5).
6. While firmly holding edges of brass
trim together, tighten both set screws
on the adjusting plate with slotted
screwdriver.
7. Repeat steps 1 through 6 for other side.
8. Tighten trim hanging screws (#10 x
6.25 shoulder) into holes in cabinets.
Place the assembled trim onto fireplace
cabinet. Align hanging notches on trim
with hanging screws on side of fireplace
(see Figure 6). Push trim firmly into
place, sliding hanging notches over
hanging screws.
NOTICE: This heater is intended
for use as supplemental heat. Use
this heater along with your pri-
mary heating system. Do not in-
stall this heater as your primary
heat source. If you have a central
heating system, you may run
system’s circulating blower while
using heater. This will help circu-
late the heat throughout the
house. In the event of a power
outage, you can use this heater
as your primary heat source.