Filter
Top Products
16
104416
UNVENTED NATURAL GAS LOG HEATER
DESA INTERNATIONAL
TEMP
STATUS
HI
LO
MAN ON
AUTO OFF
O
F
F
P
I
L
O
T
O
N
L
O
I
H
ON
OFF
REMOTE
OPERATING
HEATER
Continued
Figure 22 - Setting the Selector switch, Control Knob, and Flame Adjustment Knob for
Remote Operation
Selector Toggle Switch (Optional
Remote Control)
Control Knob in
On Position
Flame Adjustment Knob
Note:
All remote control accessories must
be purchased separately (see Accessories,
page 25). Follow instructions included
with the remote control.
Thermostat Control Operation
(Optional GHRCT Only) The thermo-
stat control setting on the remote control
unit can be set to any comfort level be-
tween HI and LO. The burners will turn
on and off automatically to maintain the
comfort level you select. The ideal com-
fort setting will vary by household de-
pending upon the amount of space to be
heated, the output of the central heating
system, etc.
For wall thermostat operation, follow in-
struction supplied with thermostat ac-
cessory GWMT1. For wall switch opera-
tion follow instructions supplied with
GWMS2.
Increases Room
Temperature
Decreases Room
Temperature
Turns Burners
On and Off
Shows Current
Operation Mode
Shows Temperature Setting
Allows Burners to be Turned
On and Off with the Hand-
Held Remote Unit.
OPTIONAL REMOTE
OPERATION
Figure 23 - Thermostat Hand-Held Remote Control Unit Selections (GHRCT Only)
The Log Heater will
Automatically Cycle between
Pilot and the Heat Setting
that has been Selected
GHRC Operation:
2a. Press the ON/OFF button to turn the
burners on and off. When turning
burners off, the pilot will remain lit.
GHRCT Operation:
2. Select the MAN (manual) or AUTO
button on the hand-held remote con-
trol unit (see Figure 23).
• In manual mode, turn burners on
or off by pressing the ON or OFF
buttons on the hand-held remote
control unit.
• In auto mode, the room tempera-
ture is controlled by the thermo-
stat in the hand-held remote con-
trol unit. To increase the room tem-
perature, press the top arrow of the
TEMP button. To lower room the
temperature, press the bottom ar-
row of the TEMP button. At higher
settings the heater will run more.
IMPORTANT:
This remote control
has been specially engineered to take
an air temperature sample every 5.5
NOTICE: You must light the pilot
before using the remote control
unit. See
Lighting Instructions
on
page 14.
1. After lighting, let pilot flame burn for
about one minute. Turn control knob
to ON position. Adjust flame adjust-
ment knob anywhere between HI and
LO. Slide the selector switch to the
REMOTE position.
NOTE:
The burn-
ers may light if hand-held remote ON
button was on when selector switch
was last turned off. You can now turn
the burners on and off with the hand-
held remote control unit.
IMPORTANT:
Do not leave the se-
lector switch in the REMOTE or ON
position when the pilot is not lit. This
will drain the battery.
IMPORTANT:
Be sure to press the
ON/OFF buttons on the hand held
remote control unit for up to 3 sec-
onds to assure proper operation.
minutes in the auto mode. It will not
respond immediately to the tempera-
ture setting being turned up or down.
IMPORTANT:
The hand-held remote
control unit must be near the heater.
Do not keep the hand-held remote
control unit too close to the heater.
The thermostat on the hand-held re-
mote control unit will heat up too
quickly and turn the heater off.
3. Use the STATUS button on the hand-
held remote control unit to see the
operation mode being used and the
temperature setting selected. A red
light will come on beside the opera-
tion mode being used when the sta-
tus button is pressed.
4. To turn the burners off when operat-
ing in the manual mode, press the OFF
button. If operating in the auto mode,
press the MAN button, then press the
OFF button. The pilot will remain lit.
IMPORTANT:
To turn the pilot off,
manually turn the control knob on the
heater to the OFF position.