Filter
Top Products
16
105442
VENT-FREE PROPANE/LP BAY FRONT FIREPLACE
CF26PR
For more information, visit www.desatech.com
LIGHTING
INSTRUCTIONS
1. STOP! Read the safety information,
column 2.
2. Make sure equipment shutoff valve
is fully open.
3. Set switch in OFF position.
NOTICE: During initial operation
of new heater, burning logs will
give off a paper-burning smell.
Open a window to vent smell. This
will only last a few hours.
WARNING: Burner will come
on automatically within one minute
when the selector switch is in the
ON position after the pilot is lit.
Figure 33 - Control Knob and Ignitor Button Location (Shown as
Supplied, No Control Options)
O
F
F
P
I
L
O
T
O
N
L
O
I
H
AUTO
OFF
ON
Control Knob
Ignitor Button
Selector Switch
Flame Adjustment Knob
4. Press in and turn control knob clock-
wise to the OFF position.
5. Wait five (5) minutes to clear out any
gas. Then smell for gas, including
near the floor. If you smell gas,
STOP! Follow “B” in the safety in-
formation. If you don’t smell gas, go
to the next step.
6. Press in and turn control knob coun-
terclockwise to the PILOT
position. Press in control knob for
five (5) seconds (see Figure 33).
Note:
You may be running this
heater for the first time after hook-
ing up to gas supply. If so, the con-
trol knob may need to be pressed in
for 30 seconds or more. This will al-
low air to bleed from the gas system.
7. With control knob pressed in, press
and release ignitor button. This will
light pilot. The pilot is attached to the
front burner. If needed, keep press-
ing ignitor button until pilot lights.
Installing 9-Volt Battery (Not
Included) in Hand-Held Remote
Control Unit
1. Remove battery cover on back of re-
mote control unit.
2. Attach terminal wires to the battery.
Place battery into the battery housing.
3. Replace battery cover onto remote con-
trol unit.
Figure 31 - Installing Battery in Hand-
Held Remote Control Unit (CGHRC Series)
INSTALLATION
Continued
Battery
Cover
9-Volt
Battery
Terminal
Wires
Remote
Control Unit
Battery
Housing
OPERATING
FIREPLACE
FOR YOUR SAFETY
READ BEFORE
LIGHTING
WARNING: If you do not fol-
low these instructions exactly, a
fire or explosion may result caus-
ing property damage, personal
injury or loss of life.
A. This appliance has a pilot which must
be lighted by hand. When lighting the
pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all
around the appliance area for gas. Be
sure to smell next to the floor because
some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL
GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do
not use any phone in your building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow
the gas supplier’s instructions.
• If you cannot reach your gas sup-
plier, call the fire department.
C. Use only your hand to push in or turn
the gas control knob. Never use tools.
If the knob will not push in or turn
by hand, don’t try to repair it, call a
qualified service technician or gas
supplier. Force or attempted repair
may result in a fire or explosion.
D. Do not use this appliance if any part
has been under water. Immediately
call a qualified service technician to
inspect the appliance and to replace
any part of the control system and
any gas control which has been un-
der water.
Figure 32 - Installing Battery in Hand-Held
Remote Control Unit (CGHRCTA Series)
Remote
Control
Unit
Terminal
Wires
9-Volt
Battery
Battery
Cover