Filter
Top Products
ENGLISH
3
• This motion activated twin floodlight should be installed by persons with experience in house-
hold wiring or by a qualified electrician. The electrical system, and the method of electrically
connecting the fixture to it, must be in accordance with the National Electrical Code and local
building codes.
• Use only with a 100 watt or smaller wattage bulb. Installing a bulb of higher wattage could
create a fire hazard. Use of a higher wattage bulb will void the warranty.
• Never touch the bulb with your bare hands, as oil from your skin can cause premature failure.
Always handle the bulb with gloves or a soft cloth.
• For supply connections, use wire rated at least 75 degrees C.
• For proper operation and protection against damage, the motion sensor head adjustment knobs
must be facing the ground.
• In the event of lens breakage, contact Customer Service for ordering assistance.
• Disassembly of your fixture will void the warranty.
SAVE THESE INSTRUCTIONS.
For best results
• Install your fixture 8-12 feet above ground (motion detector is less
sensitive above 12 feet).
• Locate fixture so motion moves across detection zone (L).
• Locate fixture away from heat producing sources to prevent
false triggering. Also be very careful not to include objects such as win-
dows, white walls and water in the detection zone whenever possible.
• Locate fixture away from moving objects such as trees and street traffic.
• Do not install more than one motion detector on one wall switch.
Installing your bulb
Step 1: Remove the lens cover by twisting it one-half turn counterclockwise.
Step 2: Using gloves or a soft cloth, gently insert bulb into housing. NOTE: Align two pins
located on the sides of the bulb with two small
slots in the socket, press bulb into spring loaded
socket and twist a half turn clockwise, until firmly
seated. Repeat this procedure for the other light.
Step 3: Replace the lens (making sure the gasket is in
place) by aligning the notches on the housing with
the cover and pressing while turning one-half turn
clockwise until seated.
Mounting your fixture
Step 1: Turn off the power at the main fuse/breaker box.
Step 2: Line up the holes on the mounting bracket with the holes on your
junction box. Using either (2) #6 screws or (2) #8 screws (depending
on size of the holes in your junction box), attach the mounting bracket
to your junction box (M).
Step 3: Hang one end of the mounting hook onto the mounting bracket
(using the hole in the bracket, see drawing), and hang the light
fixture on the other end of the mounting hook. NOTE: Carefully
hang the fixture at the base of the lampholder assembly as shown.
This will free-up your hands for wiring.
Step 4: Thread fixture wires through coverplate gasket.
Step 5: If the supply wires coming from your house are solid, you can use
the Quick-connect™ wire system to attach your Regent light
fixture. NOTE: Quick connectors can only be used with solid wire
supply leads. Simply insert the black supply wire from your house
into the quick connector with black wire coming from the fixture.
Repeat for house white wire, matching to the connector with the
white wire. Push both wires firmly into holes to insure that they are
seated properly and securely (N). It’s that easy! Proceed to Step 7.
Step 6: If the supply wires coming from your house are stranded, remove
the quick connectors from the end of the light fixture wires by turning
them repeatedly from left to right while pulling. Repeat until they
are both removed. Remember: Quick connectors can only be
used with solid wire supply leads. Do not attempt to use with
other electrical fixtures! These connectors are designed to
withstand the temperature and Voltage requirements of this
Regent product only. Once the connectors have been removed,
connect black wire to house black wire and connect white wire to
house white wire using the wire nuts provided.
Round Rectangular (horizontal) Octagonal
Your fixture mounts to the
following standard junction boxes:
(eave mount)
L
(wall mount)
M
N
Prewired
quick
connector
Solid
fixture
wire
Solid house
supply wire
SV278/SV278W I.S. 10/21/03 11:12 AM Page 3