Filter
Top Products
28
Multi-Function Door Control (Optional)
OPERATION OF THE
MULTI-FUNCTION DOOR CONTROL
Press the push button to open or close
the door. Press again to reverse the
door during the closing cycle or to stop
the door while it’s opening.
Light feature
Press the Light button to turn the opener light on or off. It
will not control the opener lights when the door is in
motion. If you turn it on and then activate the opener, the
light will remain on for 4-1/2 minutes. Press again to turn
it off sooner. The 4-1/2 minute interval can be changed to
1-1/2, 2-1/2, or 3-1/2 minutes as follows: Press and hold
the Lock button until the light blinks (about 10 seconds).
A single blink indicates that the timer is reset to 1-1/2
minutes. Repeat the procedure and the light will blink
twice, resetting the timer to 2-1/2 minutes. Repeat again
for a 3-1/2 minute interval, etc., up to a maximum of four
blinks and 4-1/2 minutes.
Lock feature
Designed to prevent operation of the door from hand-held
remote controls. However, the door will open and close
from the Door Control, the Outside Keylock and the
Keyless Entry Accessories.
To activate, press and hold the Lock button for 2 seconds.
The push bar light will flash as long
as the Lock feature is on.
To turn off, press and hold the Lock
button again for 2 seconds.The
push bar light will stop flashing. The
Lock feature will also turn off
whenever the “learn” button on the
motor unit panel is activated.
L
O
C
K
L
I
G
H
T
Lighted
Push Button
Lock
Button
Light
Button
To prevent possible SERIOUS INJURY OR DEATH from
electrocution:
• Be sure power is not connected BEFORE installing door
control.
• Connect ONLY to 24 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a
closing garage door:
• Install door control within sight of garage door, out of
reach of children at a minimum height of 5 feet (1.5 m),
and away from all moving parts of door.
• NEVER permit children to operate or play with door control
push buttons or remote control transmitters.
• Activate door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep garage door in sight until completely closed.
NEVER permit anyone to cross path of closing garage door.
WARNING
CAUTION
WARNING
WARNING
Opener Terminal Screws
2-Conductor
Bell Wire
AntennaOpener Panel
Multi-Function
Door Control Panel
Terminal Screws
KG
KG
1
3
9
7
5
1
3
9
7
5
1
2
3
Door Control
Push Bar
Light Button
Lock
Button
LOCK
L
IG
H
T
2
1
RED
WHT
INSTALLATION
Locate door control within sight of the door at a minimum
height of 5 feet (1.5 m) where small children cannot
reach, and away from moving parts of the door and door
hardware. If installing into drywall, drill 5/32" holes and
use anchors provided. For pre-wired installations (as in
new home construction), it may be mounted to a single
gang box. NOTE: After installation, a green indicator light
behind the cover will indicate proper connection. If not lit,
the Lock and Light features will not function (reverse
wires to correct).
1. Strip 1/4" (6 mm) of insulation from one end of bell
wire and connect to the two screw terminals on back
of door control by color: white wire to 2 and white/red
wire to 1.
2. Remove cover by gently pushing both thumbs against
upper corners of cover on back side of door control.
Fasten with 6ABx1-1/4" self-tapping screws (standard
installation) or 6-32x1" machine screws (into gang
box) as follows:
• Drill and install bottom screw, allowing 1/8" (3 mm) to
protrude above wall surface.
• Position bottom of door control on screw head and
slide down to secure. Adjust screw for snug fit.
• Install top screw with care to avoid cracking plastic
housing. Do not overtighten.
• Insert bottom tabs and snap on cover. (To remove
cover after mounting, gently pry at top with paper clip
or small flat head screwdriver.)
3. (Standard installation only) Run bell wire up wall
and across ceiling to motor unit. Use insulated staples
to secure wire in several places. Do not pierce wire
with a staple, creating a short or open circuit.
4. Connect bell wire to the opener terminal screws: white
to 2 and white/red to 1.
5. Use tacks or staples to permanently attach entrapment
warning label to wall near door control, and manual
release/safety reverse test label in a prominent
location on inside of garage door.
NOTE: DO NOT connect the power and operate the
opener at this time. The trolley will travel to the full open
position but will not return to the close position until the
sensor beam is connected and properly aligned. See
Safety Reversing Sensor Instructions beginning on
page 15.