Filter
Top Products
On
Select Occupied 1 to run
on this day (On), or not to __,:i_i i
run this day (Off).
ON
Off
Yes
hl¢l
IlL!
We
Select Yes or No to copy
the previous day's I _ 1_/ program to this day.
LI.,I o,J
No I ii
Selecting Yes, then pressing mode will copy the previous day's program
and then will ask the same copy question again If yes is setected each
time, this routine will repeat until Saturday is copied to Sunday After Satur-
day is copied to Sunday, the copy command is unavailable.
ft no is selected, as in previous steps, flashing prompts for input will appear
for start and stop times for Occupied 1. If more than one occupied period
was selected in Step 1 on page 3, then cool/heat set points, and start/stop
times for additional occupied periods will be prompted.
PROGRAMMING NOTES
• If only one Occupied period is selected in Step 1 on
page 3, Occupied 2 and 3 programming steps are
skipped. Further, if only 2 occupied periods are
selected, Occupied 3 programming steps are
skipped.
• Heat and Cool set points for Occupied 1 are the
same for every day of the week. Heat and Cool set
points for Occupied 2 and 3 can be adjusted differ-
ently for weekdays and weekends, if desired.
• If the start time is set later in the day than the
stop time, the program will run from the start time
to midnight and from midnight to the stop time on
the same day. For example: 9:00pm start, 8:00am
stop, on Monday, In this example the program will
run from 12:00am Monday to 8:00am Monday and
again from 9:00pm Monday to 12:00pm Monday,
• The Unoccupied settings take effect at all times
when: (1) the program is on and (2) the current time
is outside a preset occupied period. For this reason
start and stop times are not necessary for
unoccupied.
• If the same start and stop times are programmed in
for an occupied period, then it will run 24 hours.
• If one occupied period starts and stops within
another occupied period the lower occupied num-
ber has priority. For example: If Occupied 3 is pro-
grammed to be "on" 24 hours, and Occupied 2 is
programmed to run that day, then Occupied 2 set-
tings will take over from Occupied 3 between
Occupied 2 start and stop times.
'_ Press the Mode button
MODE While holdtng the Mode,
press the Override button
for 10 seconds toenter
OVERRIDE Setup screens
Adiust the time of day
clock,
Tip To change hours quickly, press and
hoedtheoverride bulton in and press
theuporduwnbuttons
NOTE Each step number is located at
the top tight corner of the disiay
for easy reference
/
Select the day of the
week.
Select fan operation,
Fan dl or Fan Auto.
I!I = Low Speed Fan= Medium Speed Fan
III= High Speed Fan
On
?y selectHea Poopoooro.
AUTO
Adiust the deadbend
from 1 to6 degrees F.
Fan
Adiust the minimum
difference between
cooling and heating
_ sel points.
(0_to6 F)
J_
3
(_ Select the cycles per
hour limit.
d=cycles per hour
limit defeated.
dl =d +defeat 5 rain.Compressor lockout.
(d, dl, 2- 6)
Select the security level:
O=no security in effect
_/) 1=set point range limited2=1 + program on all times
3=2 + prohibits set point
changes
J
(_ Adjust the maximum
alowable heat set point
when security is ineffect.
(Step 8only appearsif Step 9 is not 0.)
(35 tO 99 F)
M
M
OFF
Page 4