Black & Decker fsmh1621 Carpet Cleaner User Manual


 
9
ENGLISH
(Original instructions)
Caution! It is important to monitor the water level in the water
tank. To rell the water tank and continue to sanitise/clean, re-
turn the handle (10) to the upright position and turn the steam
mop ‘OFF’. Unplug the unit from the electrical wall outlet, rell
the water tank (8).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop on
the resting mat (13) with the handle (10) in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
After use (Fig. L & M)
u Return the handle (10) to the upright position and turn the
steam mop ‘OFF’,
u Place the steam mop on the resting mat (13) and wait until
the steam mop cools down. (approximately ve minutes)
u Unplug the steam mop from the electrical wall outlet.
u Empty the water tank (8).
u Remove the cleaning pad (12) and wash it ready for
next use. (Take care to follow the wash care instructions
printed on the cleaning pad).
u Wrap the supply cable around the cable tidy hooks (15 &
16).
Note: The top cable tidy hook (16) rotates to easily release
the cable ready for next use.
u Clip the supply cable onto itself using the cable tidy clip
(29) close to the plug.
u Place steam mop on the resting mat (13) for storage.
Note: With the handle (10) in the upright position, the cable
neatly wrapped around the cable tidy hooks (15 & 16) and
secured with the cable tidy clip (29) your steam mop will stand
on its own for storage. Alternatively there is a hanging bracket
(30) built into the hand grip (31) which will allow your steam
mop to be hung from a suitable hook on the wall. Always
ensure that your wall hook is capable of supporting the weight
of the steam mop safely.
Hand held steam cleaning
u Attach the required accessory.
u Connect the hand held steam cleaner to the mains.
u Press the ON/OFF button (1). It takes approximately 15
seconds for the hand held steam cleaner to heat up.
u Lift the lock off (2) and pull the trigger switch (3) to activate
the steam pump. After a few seconds steam will start to
come out of the accessory.
Note: When rst lled or after running dry it can take up to 45
seconds for steam to be produced.
Note: During use you may turn off the steam pump by releas-
ing the trigger switch, this convenient feature will allow you to
place the hand held steam cleaner down for a short time so
that you may move items of furniture, then continue cleaning
without the need to switch the appliance off.
u When you have nished using the hand held steam
cleaner, release the trigger switch (3), turn it ‘OFF’ and
disconnect from the mains supply. Wait until the steam
mop cools down before storing. (approximately ve
minutes)
Caution! It is important to monitor the water level in the water
tank. To rell the water tank and continue to sanitise/clean,
turn the hand held steam cleaner ‘OFF’. Unplug the unit from
the electrical wall outlet, rell the water tank (8).
Caution! Steam may continue to be produced for a short time
after the trigger switch (3) is released, this is normal. Switch
off and allow the unit to cool before removing any accessories.
Technical data
FSMH1621
(Type 1)
Voltage V
ac
230
Power W
1600
Tank capacity ml
350
Weight kg 3.6
Troubleshooting
If your appliance seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local Black & Decker repair agent.
Problem Step Possible solutions
The steam mop is
not turning on.
1
Check the unit is plugged in at the wall
socket.
2
Check the unit is switched on using the on/
off switch (1).
3 Check the fuse in the plug.
The digital controls
do not light up.
4
Check that the handle (10) of the steam mop
is pushed rmly into the steam mop body (9).
Check that the arrow on the handle is ush
with the top of the steam mop body (9).
5
Check that the hand held steam cleaner (5)
is rmly docked into the steam mop body (9).
6 Check steps 1, then 2, then 3.