Filter
Top Products
6
ENGLISH
(Original instructions)
Attaching the hand held steam cleaner (Fig. C)
u Holding the back of the steam mop body (9) Push the
hand held steam cleaner (5) rmly into the steam mop
body (9) until it clicks into place.
Caution! Always ensure the handle command lights up to
conrm the unit is docked.
Warning! Inspect that the seal (22 Fig. H) on the steam noz-
zle (4) before tting the hand held steam mop to the steam
mop body. If the seal is missing or damaged then please
contact your nearest authorised repair agent. Do not use the
appliance.
Removing the hand held steam cleaner (Fig. C)
u Push the release button (19) down and pull the hand held
steam cleaner (5) away from the steam mop body
Attaching a cleaning pad (Fig. D)
Replacement cleaning pads are available from your Black &
Decker dealer:-
Steam head cleaning pad - cat. no. FSMP20-XJ).
u Place a cleaning pad (12) on the oor with the ‘hook &
loop’ side facing up.
u Lightly press the steam mop down onto the cleaning pad
(12).
Caution! Always place your steam mop on the resting mat
(13) with the handle (10) in the upright position when station-
ary and make sure the steam mop is turned off when not in
use.
Removing a cleaning pad (Fig. E)
Caution! Always wear suitable shoes when changing the
cleaning pad on your steam mop. Do not wear slippers or
open toed footwear.
u Return the handle (10) to the upright position and turn the
steam mop ‘OFF’.
u Place the steam mop on the resting mat and wait until it
cools down. (approximately ve minutes)
u Place the front of your shoe onto the cleaning pad removal
tab (21) and press down rmly.
u Lift the steam mop up off the cleaning pad.
Caution! Always place the steam mop on the resting mat (13)
with the handle (10) in the upright position when stationary
and make sure the steam mop is turned off when not in use.
Filling the water tank (Fig. F)
This Steam cleaner incorporates an anti-calc system to help
prolong the life of the system.
Note: Fill the water tank with clean tap water.
Note: In areas of very hard water, the use of de-ionised water
is recommended.
u Open the ller cap (7) by ipping it down.
u Using the jug, ll the water tank (8) with water.
Warning! Your water tank has a 0.35 litre capacity.
u Re-t the ller cap (7).
Note: Ensure the ller cap is rmly secured.
Note: When not in use, the jug (18) may be clipped to the
handle for convenient storage.
Note: Do not use chemical cleaners with your steam mop..
Attaching the carpet glider (Fig. G) (For use on
carpets only)
u Place carpet glider on the oor.
u Attach a cleaning pad to the unit.
u Lightly press the steam mop down onto the carpet glider
(14) until it clicks into place.
Caution! Always place the steam mop on the resting mat (13)
with the handle (10) in the upright position when stationary
and make sure the steam mop is turned off when not in use.
Removing the carpet glider (Fig. G)
Caution! Always wear suitable shoes when changing the
carpet glider on your steam mop. Do not wear slippers or
open toed footwear.
u Return the handle (10) to the upright position and turn the
steam mop ‘OFF’.
u Place the steam mop on the resting mat and wait until it
cools down. (approximately ve minutes)
u Place the front of your shoe onto the carpet glider removal
tab (33) and press down rmly.
u Lift the steam mop up off the carpet glider (14).
Caution! Always place the steam mop on the resting mat (13)
with the handle (10) in the upright position when stationary
and make sure the steam mop is turned off when not in use.
Attaching the hose and accessories to the Hand
held steam cleaner (Fig. H & I)
Warning! Inspect the seal (22) on the steam nozzle (4) and
hose (23) before each use. If the seal is missing or damaged
then please contact your nearest authorised repair agent. Do
not use the appliance.
Attaching the hose (Fig. G)
u Press in the clips (24) on either side of the hose (23).
u Press the hose (23) onto the steam nozzle (4) and release
the clips (24).
Important! Ensure that the hose (23) is securely fastened
before using the hand held steam cleaner. If steam escapes
from the joint then the hose is not correctly t, allow the unit to
cool then remove and re-t the hose.
Attaching the variable steam jet nozzle (Fig. I)
u Press in the clips (26) on either side of the variable steam
jet nozzle (27).
u Press the variable steam jet nozzle onto the steam nozzle
(4) or the hose (23) and release the clips (26).