Filter
Top Products
3.1) you can choose from; 1, 2, 3, 4, 5, 6, 7, 8
hours
3.2) 1 through 8 will scroll in a continuous loop
4) After you have made your selection, the whole screen
flashes for 5 seconds after last button push of + or -
then goes back to previous mode
4.1) "timer" remains lit to show the timer function
has been set.
5) At any time if you unlock the remote and push
the mode button to turn the unit off the timer
setting will be erased and "timer" will disappear
from the remote.
6) To check how much time is remaining, press and hold
the + and – buttons simultaneously.
Using Timer to turn unit on
This function is meant for a person to preheat a room by
setting the timer. For Example: It’s 8 am, and you want to
come home to a warm room at 8 pm. To accomplish this
place the unit in the desired room and set the timer to
turn the unit on in 12 hours. Once the timer is activated
the unit will run for a preset time of 2 hours. The digital
thermostat will maintain the room temperature at a
default of 72ºF.
1) Hold mode button for 2 seconds to unlock remote.
2) DO NOT push mode again as this will turn unit on.
3) Push + and - together.
3.1) Unit remains off.
3.2) "timer" and "auto - high" turns on and
flashes on the remote, and 1 Hr appears on
the screen
4) Push + or - to adjust the number of hours that will
pass before it turns itself on.
4.1) you can choose from; 1, 2, 3, 4, 5, 6, 7, 8,
9, 10, 11, 12, 13, 14, 15, 16 hours
4.2) 1 through 16 will scroll in a continuous loop
5) The whole screen flashes for 5 seconds after last
button push of + or - then goes back to previous
mode
5.1) The timer will turn the unit on and run for 2
hrs. During the 2 hours, the digital
thermostat will maintain the room in auto –
high at the default of 72º F.
8
DO NOT DEFEAT THE SAFETY PURPOSE OF THIS
GROUNDED PLUG IN ANY WAY.
The length of the cord used on this product was selected
to reduce the hazards of becoming tangled in, or tripping
over a longer cord. If a longer cord is necessary an approved
extension cord may be used. The electrical rating of the
extension cord must be equal to or greater than the rating
of the heater. Care must be taken to arrange the extension
cord where it cannot be pulled on by children or accidentally
tripped over.
This device complies with Part15 of the FCC Rules.
Operation is subjected to the following two conditions: (1)
this device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
AUTO SHUT-OFF
This heater is equipped with a patented, technologically-
advanced safety system that requires the user to reset the
heater if there is a potential overheat situation. When a
potential overheat temperature is reached, the system will
automatically shut the heater off. It can only resume
operation when the user resets the unit.
To Reset the Heater:
1. Unplug the heater and wait 20 minutes for the unit to
cool down
2. After the 20 minutes, plug the unit in again and operate
normally.
HOW YOUR BIONAIRE
®
CONSOLE HEATER WORKS
Your Bionaire
®
heater uses natural convection heat to draw
cool air in and exhale warm air without the use of a fan.
Within this unit are heat-panel filaments that get warm in a
matter of seconds and hold their temperature evenly. The
air surrounding these filaments heats up, rises, and flows
out into the room. Cooler air is then drawn in to replace the
warm air and the process continues like a revolving door.
Because there is no fan, there is almost no noise.
PRE-OPERATING INSTRUCTIONS
1. Carefully remove your heater from the box (please save
the carton for off-season storage).
2. Place heater on firm level surface with wheels installed.
3