Filter
Top Products
Part No. 890311 Form No. F010396C
Page 12 of 12
Qty.Part No.
Description
Item
No.
KD505SPQ
Parts List
continued from
page 11.
1919
1919
19
86 WHEEL WITH SPROCKET ASS’Y CAST (21, 94, 95, 96) 900512 2
87 CHAIN 52 PITCH 890239 2
88 CHAIN 40 PITCH 900323 1
89 WASHER FLAT 5/16 (3/8 ID x 7/8 x 1/16) *8171003 4
90 BOLT CARRIAGE 5/16 -18 x 3/4 *8024039 4
91 WASHER SPRING LOCK 5/16 *8177011 4
92 NUT REGULAR 5/16-18 *8142002 4
93 JACKSHAFT 900320 1
94 SPROCKET (PER ASSEMBLY) 26 TEETH (Size 65A26) 890238 1
95 SCREW SELF TAP 1/4-14 x 3/4 (PER ASSEMBLY) 800505 5
96 WASHER LOCK EXTERNAL TOOTH (PER ASSEMBLY) *8181007 5
97 JACKSHAFT ASS’Y
(INCLUDE. 93, 101, 102, 107, 108, 109) 890197 1
98
99 LABEL CLUTCH 830503 1
100 LABEL-DANGER GUARDS 900327 1
101 BEARING PLATE 900317 2
102 BEARING BALL (WITH SNAP RING) 900321 2
103 WASHER LOCK 1/4 *8177010 4
104 ROD BAIL CLUTCH 900970 1
105 BAR BRACE HANDLE 900768 1
106 SCREW CAP 5/16-18 x 3/4 *8041026 1
107 SPROCKET - 17 TOOTH 900303 1
108 SPROCKET - 8 TOOTH 900302 2
109 ROLL PIN 3/16 DIA. x 1 1/4 LG. *8195166 4
110 LOCKNUT 5/16 - 18 FLANGE 850164 5
112 BRACKET CONTROL ASS’Y (INCL. 113, 114, 115) 900221 1
113 SPRING 900136 1
114 ROLL PIN 1/8” DIA. x 1 1/4 LG. *9195106 1
115 ROD CLUTCH 900208 1
116 SCREW CAP 1/4-20 x 1/2” LG. *8041002 3
117 WASHER 1/4” FLAT (5/16 ID x 3/4 OD x 1/16) *8171002 8
118 GUARD CHAIN ASS’Y 890231 1
119 CLIP-CLUTCH CABLE 900999 1
120
121 CLUTCH DOUBLE RELEASE 900307 1
122 WASHER FENDER 5/16 *8172020 1
123 LABEL READ OWNER'S MANUAL 890301 1
* Denotes
standard
hardware item
that may be
purchased
locally.
SolutionSolution
SolutionSolution
Solution
ProblemProblem
ProblemProblem
Problem
Possible CausePossible Cause
Possible CausePossible Cause
Possible Cause
TRTR
TRTR
TR
OUBLESHOOOUBLESHOO
OUBLESHOOOUBLESHOO
OUBLESHOO
TINGTING
TINGTING
TING
Before Requesting Service Review These Suggestions
Will not vacuum or has poor
vacuum performance.
Clean debris bag. Shake bag clean or wash. Adjust nozzle height.
Check for hose kit cap. Unclog nozzle or exhaust (see page 5).
Allow air to feed with debris.
Dirty debris bag. Nozzle height set too high or too low. Hose kit cap
missing. Clogged nozzle or exhaust. Excessive quantity of debris.
Engine will not start.
Self propelled drive will not
release .
Clutch cable out of adjustment. Clutch not lubricated and is locked-up.
No self propelling.
Operator's bail not releasing clutch. Broken or out of adjustment
clutch cable. Worn or broken clutch assembly. Bracket control
assembly (item 112) out of adjustment.
Throttle in off position. Out of gasoline. Bad or old gasoline.
Spark Plug wire disconnected. Dirty air cleaner.
Abnormal vibration.
Loose or out of balance impeller or loose engine.
Check impeller and replace if required. Check Engine.
Engine is locked, will not
pull over.
Debris locked inside impeller. Engine problem. See page 5, Contact an engine servicing dealer for engine problems.
Check stop switches, throttle, and gasoline. Connect spark plug wire.
Clean or replace air cleaner. Or contact a qualified service person.
Adjust clutch cable. See page 9 Clutch Adjustment. Oil clutch.
Adjust clutch cable. Adjust bracket control assembly. Replace any
worn or damaged or malfunctioning parts.
2020
2020
20
2222
2222
22
BILLY GOAT INDUSTRIES INC.
P.O. BOX 308 (1803 S JEFFERSON LEE'S SUMMIT, MO 64063 / USA
PHONE: 816-524-9666 FAX: 816-524-6983
R
WARRANTY PROCEDURE
Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:
The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.
The owner should present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.
The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.
The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and
binding.
Note:
To process a Warranty Claim, it is necessary to quote the Model
& Serial number who are printed on the Billy Goat Serial Plate.
Purchased
from
Purchase
Date
2121
2121
21
Serial Plate
Record your machine model, serial number
and date-of-purchase and where purchased
R
min
-1
Operator
1803 S. Jefferson
P.O. Box 308
Lee's Summit,
MO 64063 / USA
Tel (816) 524-9666
Fax (816) 524-6983
Model Serial No.
Unit(Weight) Engine Power
lbs. kg kW rpm
L
A
p
108
95
L
A
Engine Service and Warranty
22.122.1
22.122.1
22.1
Contact your nearest engine manufacturer's autho-
rized servicing dealer.