Filter
Top Products
Part No. 800012 Form No. F021402A
BG VACUUM
95
99
5
Page 3 of 12
For your safety and the safety of others, these directions should be followed:
Use of Ear Protection is recommended while
operating this machine.
Do not operate this machine without first reading
owner's manual and engine manufacturer's manual.
Use of Eye and Breathing protection is recom-
mended when using this machine, especially in dry
and dusty conditions. Optional bag cover directs dust
toward ground, away from the operator.
·DO NOT place hands or feet inside nozzle intake opening, near
debris outlet or near any moving parts.
·DO NOT start engine without debris bag and quick discon-
nect connected firmly in place to exhaust outlet.
GENERAL SAFETY
99
99
9
·DO NOT start or operate machine with debris bag zipper open.
·DO NOT operate during excessive vibration.
·DO NOT remove bag until engine has been turned off and has
come to a complete stop.
·DO NOT remove hose kit cap on nozzle until engine has been
turned off and has come to a complete stop.
·DO NOT operate machine with hose cap, bag or hose removed.
·DO NOT use this machine for vacuuming exclusively sand,
dust, fine dirt, rock, glass, string like material, grain, rags,
cans, metal, bark or water.
·DO NOT operate this machine on slopes greater than 20%.
·DO NOT pick up any hot or burning debris, or any toxic or
explosive material.
·DO NOT allow children to operate this equipment.
PUT OIL IN ENGINE BEFORE STARTING.
Read all safety and operating instructions
before assembling or starting this unit.
ASSEMBLY
1010
1010
10
Rod Lever
810162
Self Propelled Only
Per Model
Boxing Checklist
Handle Bail Assy
SP
Units Only
810164
Handle Assy
Push
Units Only
800043
All Models
Debris Bag
800730
Elbow Assembly
800967
Check
Check
Check
Check
These items should be included in your carton. If any of
these parts are missing, contact your dealer.
Check
Check
Your Billy Goat is shipped from the factory in one carton, completely assembled
except for the debris bag, upper and lower handles, handle brace, nozzle control
rods, exhaust elbow, gasket, and (sp only) rod lever shift assy.
1 Lower handles: Assemble lower handles (items 60, 61) to engine base using
washers (item 17) and lock nuts (item 5).
HAND TIGHTEN ONLY.
2 Upper Handle, Handle Braces:
2.1 Assemble upper handle (item 47), and handle braces (items95 and 99) to
lower handles using screws (item 40), washers (item 17) and lock nuts (item 5)
with ends of handle brace on inside of handle and screw heads facing inward,
toward debris bag, otherwise premature bag wear could result.
HAND TIGHTEN ONLY.
2.2 After elbow assembly has been installed, attach front of handle braces
(items 95 and 99) to 3/8 inch stud on elbow mounting flange, using lock nut
(item 43).
3. Tighten all handle screws and nuts on lower handles, upper handle and handle
brace.
4. Throttle control (item 52):
4.1 Attach throttle to upper handle using screw (item 21) and lock nut (item 18).
4.2 Attach throttle control conduit to handles using cable clamps (item 93).
Boxing Checklist
Engine Manual
Briggs & Stratton
10 HP Intek
Check
Brace Handle LH
800821
Per Model
Check
Check
Check
Parts Bag & Lit.
Assy.
Check
Handle Lower R.H.
800943
Check
Link 810987
Check
Handle Lower L.H.
800933
BG1002
800014
PACKING CHECK LIST
5. Nozzle door control rods (items 55, 59):
5.1 Attach end of link (item 59) with single hole to nozzle door mounting hole
using screw (item 54), washers (item 17-2 req'd) and lock nut (item 18).
5.2 Assemble link (item 55) to lever assembly (item 56) using screws (item
54), washers (item 17-2 req'd) and lock nuts (item 18).
5.3 Attach link ends (item 59, 55) to each other in 2 holes using screw (item
21), washers (item 17) and lock nut (item 18).
6. Elbow Assembly (item 2):
Attach elbow assembly (item 2) and flange gasket to exhaust outlet of main
unit using screws (item 17) and lock nuts (item 5).
7. Debris Bag (item 1):
7.1 Attach neck of debris bag onto elbow assembly.
SECURELY TIGHTEN BAG NECK STRAP.
7.2 Attach bag hanger clips to bag loops (item 50) preassembled to upper
handle.
8.
SP MODEL ONLY
. Rod Lever Shift Assy.
8.1 Remove eye bolt (item 45), from hardware bag and slide curved end of rod
through eye bolt (item 45).
8.2 Slide curved end of Rod Lever Shift (item 90) through hole in shift bracket
located on rear of transmission so that shift lever end of rod is up. Reinstall
eye bolt (item 45) and hardward through upper handle and clutch cable
mounting bracket.
9. Attach "z" end of cable (item 86) to inside of bracket on rod bail assy (item 88).
10. Connect spark plug wire.
1111
1111
11
BG1002SP
800015
Denotes parts found in
Parts Bag Assembly
(shown on page 4).
Bar Link Upper
811061
Brace Handle RH
800822
Check