Filter
Top Products
Part No. 800012 Form No. F021402A
Page 12 of 12
Purchased
from
Purchase
Date
1803 S. Jefferson P.O. Box 308
Lee's Summit, MO 64063 / USA
(816) 524-9666 (816) 524-6983
Model
Serial No.
lbs
kw
kg
Engine Power
Unit (weight)
h p
Solution
Problem Possible Cause
TROUBLESHOOTING
Before Requesting Service Review These Suggestions
2121
2121
21
22.122.1
22.122.1
22.1
2222
2222
22
Engine Service and Warranty
Contact your nearest engine manufacturer's autho-
rized servicing dealer.
Serial Plate
Record your machine model, serial number
and date-of-purchase and where purchased
Will not vacuum or has poor
vacuum performance.
Clean debris bag. Shake bag clean or wash. Adjust nozzle height.
Check for hose kit cap. Unclog nozzle or exhaust (see page 5).
Allow air to feed with debris.
2020
2020
20
Dirty debris bag. Nozzle height set too high or too low. Hose kit cap
missing. Clogged nozzle or exhaust. Excessive quantity of debris.
Engine is locked, will not
pull over.
Debris locked inside impeller. Engine problem.
See page 5, Contact an engine servicing dealer for engine problems.
See Chain Adjustments on page 11.
Noisy or broken chain
Self propelled drive will not
release
Sticking belt idler arm. Belt fingers out of adjustment, bent or broken.
Check idler. Idler arm mounting screw may be too tight or too
loose. Check wire belt guide adjustment. Replace if broken. (see
fig. 3 & 4 adjustment on page 11).
No self-propelling
Check transmission gear selection. Check clutch cable
adjustment and belt and chain (See page 11).
Engine will not start.
Check stop switches, throttle, and gasoline. Connect spark plug wire.
Clean or replace air cleaner. Or contact a qualified service person.
Abnormal vibration.
Check impeller and replace if required. Check Engine.
Loose or out of balance impeller or loose engine.
Throttle in off position. Out of gasoline. Bad or old gasoline.
Spark Plug wire disconnected. Dirty air cleaner.
Transmission not in gear. Operator's bail not engaging belt or out of
adjustment. Worn out or broken belt. Broken or mispositioned belt.
No chain lubrication. Chain out of alignment or over tensioned.
CAUTION
READ OWNER'S MANUAL
BEFORE OPERATING, MAKE SURE:
USE PROTECTION
EXHAUST ELBOW IS ATTACHED.
EXHAUST IS DISCHARGING INTO
ENCLOSED CONTAINER.
ALL GUARDS ARE ATTACHED.
HOSE IS ATTACHED.
USE ONLY A QUALIFIED MECHANIC TO SERVICE THIS MACHINE.
INSPECT MACHINE BEFORE EACH USE AND REPLACE ANY
WORN AND DAMAGED PARTS.
ABRASIVE DEBRIS WILL SHORTEN UNIT LIFE.
830138
OPERATING INSTRUCTION IS OBTAINED.
STOP ENGINE AND ALLOW TO
COOL BEFORE REFUELING.
KEEP ENGINE CLEAN OF DEBRIS.
PROPERLY SECURE EQUIPMENT BEFORE TRANSPORTING.
NEVER SERVICE UNIT WITHOUT DISCONNECTING SPARK PLUG WIRE.
Reference: Label CAUTION
Part No. 830138
BILLY GOAT INDUSTRIES INC.
1803 S.W. JEFFERSON STREET; LEE'S SUMMIT, MO 64082-2312 / USA
PHONE: 816-524-9666 FAX: 816-524-6983 www.billygoat.com
WARRANTY PROCEDURE
Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:
The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.
The owner should present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.
The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.
The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and
binding.
Note:
To process a Warranty Claim, it is necessary to quote the Model
& Serial number who are printed on the Billy Goat Serial Plate.
R
118 dB