Filter
Top Products
Connection to the CT240
The TH106 is designed to connect directly to the CT240 telephone controller.
This combination allows the activation and deactivation of the Vacation mode
from the CT240 or the telephone.
Connect the CT240’s terminals A and C to the TH106’s terminals X and C
respectively. You must respect the polarity. The signal given by the CT240 is a
low voltage signal and must not circulate in the electrical box. The wire must run
on the exterior side of the electrical box to join the thermostat.
Use a 18 to 22 gauge flexible wire and pass it behind the thermostat through the
slot located in front of the connector.
For details on operating the telephone controller, refer to the CT240’s
Instruction Manual.
PROGRAMMING
Programming the time and day
1- Set the time using the Hour and Min buttons.
2- Set the day using the Day button.
Programming the Comfort, Economy and Vacation settings
The Comfort , Economy and Vacation settings respectively represent
the temperatures that you wish to have during the day , at night or while you
are away at work , or while you are away for an extended period .
To program your settings
a) To program the Comfort temperature, select the desired degree using the
buttons and press the button until the icon is displayed (app. 3
seconds).
OPERATING MODES
The TH106 has two (2) operating modes :
MANual ( )
This mode allows you to maintain a constant ambient temperature.
1- To activate this mode, press on Mode button to display the icon.
2- Set the desired temperature using the buttons or select the pre-
programmed , or settings.
(To select the setting, press on and simultaneously.)
!
"
#$
!
Replace the front part of the thermostat on
the base and secure them in place with
the screw.
NOTE : All cables and connections must conform to the local electrical code.
WARNING : Special CO/ALR solderless connectors must be used when con-
necting with aluminium conductors.
Power-up
When power is applied for the first time, the dis-
play must show the time 0:00, the ambient tem-
perature and the Manual mode icon ( ). Other
information might show up on the display if
installation is defective or does not comply with
the instructions.
500 watts or less installation
During the 30 minute period following the instal-
lation or a long power failure (more than 2 hours),
the light intensity of the display decreases when
a button is pressed on while the thermostat is in
the heat mode. This problem will disappear when
the accumulator for the memory backup will be
charged.
Set the 4 switches located at the back of the
thermostat to your preferences.
1: Cycles of 15 min. (fan) or 20 sec.
2: Early Start
3: Time display in 12 or 24 hours
4: Temperature display in °C or °F
b) To program the Economy temperature, select the desired degree using the
buttons and press the button until the icon is diplayed (app. 3
seconds).
c) To program the Vacation temperature, select the desired degree using the
buttons and press on the and buttons simultaneously until
the icon is displayed (app. 3 seconds).
d) Press the Mode button to exit this function and return to the normal operating
mode.
Schedule programming
The TH106 allows 4 setting changes for each day of the week. There are no
pre-set programs. The programs are tailored to perfectly adapt to your life style.
The principle is very simple. For each day, enter the time at which you awake
(P1), the time you leave for work (P2), the time you arrive back home (P3) and
the time you go to bed (P4).
920-106-001-00-1-B 2/4
NOTE 1: This thermostat has been factory set to proportionally control electric
baseboards, radiant systems and convectors. Since proportional control uses a
fast commutation rate, it is not compatible with fan equipped systems (see
characteristics). Also, this control mode could occasionally create light flickering,
especially in rural area.
By switching to the 15 minute cycle mode, the thermostat will be compati-
ble with fan equipped systems.
NOTE 2: The thermostat is providing a built-in function enabling it to calculate
the optimum time to start the heating system to achieve the desired tempera-
ture setting at the programmed time. To enable this function, set the switch E.S.
to “ON” at the back of the thermostat.
AUTOmatic ( )
This mode executes your own programming.
To activate this mode, press on Mode button to display the icon. The or
icon indicates which temperature setting is used.
TELEPHONE CONTROLLER
The TH106 incorporates a telephone controller interface which allows you to
switch from the normal operating mode to the Vacation setting ( ), and vice
versa, using the telephone keypad (stationary or portable). You can, for exam-
ple, heat your country house from your office on Friday, or your house from the
airport or from your car on your way back from vacation. When the telephone
controller sends a signal, the icon appears on the screen.