Filter
Top Products
3
GENERAL INFORMATION
TO THE INSTALLER
Before installing this unit please read this manual and the Product
Data Book applicable to your model* to familiarize yourself on the
specific items which must be adhered to such as maximum external
static pressure to unit, air temperature rise, minimum or maximum
CFM and motor speed connections.
TO THE OWNER
It is important to complete the owner registration card and mail it
immediately. This will assist us in contacting you if any service or
warranty information should change in the future. When completing
the registration card, be sure to include the Model, Manufacturing
and Serial Numbers, plus the installation date.
The warranty certificate is also supplied with the unit. Read the war-
ranty carefully and note what is covered. Keep the warranty certifi-
cate in a safe place so you can find it if necessary.
If additional operating instructions are required, call the dealer where
the purchase was made. Keep this literature in a safe place for fu-
ture reference.
UNIT PLACEMENT
WARNING
T
O PREVENT POSSIBLE EQUIPMENT DAMAGE, PROPERTY DAMAGE, PERSONAL
INJURY OR DEATH, THE FOLLOWING BULLET POINTS
MUST BE OBSERVED
WHEN INSTALLING THE UNIT.
ALL INSTALLATIONS:
Ground Level Installations Only:
• When the unit is installed on the ground adjacent to the
building, a level concrete (or equal) base is recommended.
Prepare a base the same physical size as the unit or slightly
larger and 3 inches thick.
• The base should also be located where no runoff of water
from higher ground can collect in the unit.
Rooftop Installations Only:
• To avoid possible personal injury or property damage, the
roof must have sufficient structural strength to carry the
weight of the unit(s) and snow or water loads as required by
local codes.
• If horizontal air delivery is used, the unit may be installed
directly on wood floors or on Class A, Class B, or Class C
roof covering material.
• To avoid possible personal injury, a safe, flat surface for
service personnel must be provided.
• If vertical air discharge is used and the unit is installed on
combustible flooring or class A, B, or C roofing material,
then the Amana
®
brand roof curb (PRC06A1 or PRC08A1)
is required.
This unit is approved only for an outdoor installation. To assure
that your unit operates safely and efficiently, it must be installed,
operated, and maintained in accordance with these installation and
operating instructions, all local building codes and ordinances.
The heating and cooling capacities of the unit should be greater than
or equal to the design heating and cooling loads of the area to be
conditioned. The loads should be calculated by an approved method
or in accordance with A.S.H.R.A.E. Guide or Manual J - Load Cal-
culations published by the Air Conditioning Contractors of America.
Obtain from:
American National Standards Institute
1430 Broadway
New York, NY 10018
TRANSPORTATION DAMAGE
All units are securely packed in shipping containers tested accord-
ing to International Safe Transit Association specifications. The car-
ton should be checked upon arrival for external damage. If damage
is found, a request for inspection by carrier agent should be made in
writing immediately.
The unit should be carefully inspected upon arrival for damage and
bolts or screws which may have loosened in transit. In the event of
damage, the consignee should:
1. Make notation on delivery receipt of any visible damage to
shipment or container.
2. Notify carrier promptly and request an inspection.
3. In case of concealed damage, carrier should be notified as
soon as possible-preferably within 5 days.
4. File the claim with the following supporting documents within
the 9 month statute of limitations.
a. Original Bill of Lading, certified copy, or indemnity bond.
b. Original paid freight bill or indemnity in lieu thereof.
c. Original invoice or certified copy thereof, showing trade and
other discounts or reductions.
d. Copy of the inspection report issued by carrier
representative at the time damage is reported to the carrier.
The carrier is responsible for making prompt inspection of
damage and for a thorough investigation of each claim.
The distributor or manufacturer will not accept claims from
dealers for transportation damage.
NOTE: When inspecting the unit for transportation damage, remove
all packaging materials. Recycle or dispose of the packaging mate-
rial according to local codes.
RIGGING AND HANDLING
WARNING
T
O PREVENT PROPERTY DAMAGE, THE UNIT SHOULD REMAIN IN AN UPRIGHT
POSITION DURING ALL RIGGING AND MOVING OPERATIONS.
T
O FACILITATE
LIFTING AND MOVING WHEN A CRANE IS USED, PLACE THE UNIT IN AN
ADEQUATE CABLE SLING.
IMPORTANT: If using bottom discharge with roof curb, ductwork
should be attached to the curb prior to installing the unit. Ductwork
dimensions are shown in Amana
®
brand roof curb installation instruc-
tions.
Refer to the Roof Curb Installation Instructions for proper curb in-
stallation. Curbing must be installed in compliance with the National
Roofing Contractors Association Manual.
NOTE: Lower unit carefully onto roof mounting curb. While rigging
unit, center of gravity may cause condenser end to be lower than
supply air end.
*NOTE: Please contact your distributor or our website for the applicable product data book referred to in this manual.