Weil-McLain BCP-8X Boiler User Manual


  Open as PDF
of 28
 
14
%&36,QVWDOODWLRQDQG2SHUDWLRQ0DQXDO
67$57836(77,1*6
Can be accessed by holding down the Menu button for over three seconds.
352*5$0&+$1*(6(77,1*6
To be able to change the BCP-8S settings the Program/Run Switch must be set to Program.
The switch is located under the Enclosure Wiring Cover for security. The Enclosure Wiring
Cover can be securely closed using a padlock.
PROGRAM RUN
67$57836(48(1&(
Hold Button: MENU/<System Startup>
 :KHQSRZHUHGWKH%&36SHUIRUPVDVHOIWHVWRQLWVFRPSRQHQWV$IWHUWKHVHOIWHVW
GLDJQRVWLFVKDYHEHHQVXFFHVVIXOO\FRPSOHWHGWKH%&36ZLOOLQLWLDOL]HWKHSDQHO
 2QWKH¿UVWSRZHUXSWKH6\VWHP6WDUWXSVFUHHQZLOODSSHDUDIWHUWKHLQLWLDOL]DWLRQLV
FRPSOHWH,ILWGRHVQRWWKH%&36KDVDOUHDG\EHHQFRQ¿JXUHG
ARE YOU SURE?
No
Yes
BACK SAVE
 7KH6\VWHP6WDUWXSPHQXVHWVWKHPDLQSDUDPHWHUVDVWKHW\SHRIVHQVRUWKHVHTXHQFLQJPRGHDQGPDQ\RWKHUSDUDPHWHUV
described in this section.
 %HIRUHHQWHULQJWKH6WDUWXSPHQXVHYHUDOZDUQLQJVZLOODOHUW\RXWRWKHFRQVHTXHQFHVRIPDNLQJ6WDUWXSFKDQJHV
&21752/02'(
6HW3RLQW(06P$ 'HIDXOW6HW3RLQW
Hold Button: MENU/<System Startup>/..../Control Mode
 6HW3RLQWPRGHGRHVQRWUHTXLUHDQRXWGRRUVHQVRU,IDQRXWGRRUVHQVRULVFRQQHFWHG
in Set Point mode it will be used only as an Outdoor Cutoff point. That is, to turn the
stages, system, and Comb. Air relays off.
 7KH(06P$RSWLRQDOORZVWKH%&36WRUHFHLYHDQH[WHUQDOVHWSRLQWIURPDQ
EMS/BMS system. This requires the use of the 420MOD Interface (389-900-226).
 <RXPXVWVHOHFWWKHP$PLQDQGP$PD[6HW3RLQWVLQWKHIROORZLQJVFUHHQV
--- CONTROL MODE ---
Set Point
EMS 4-20mA
BACK SAVE
--- SENSOR TYPE ---
Pressure 15psi
Pressure 30psi
Pressure 100psi
Pressure 200psi
Pressure 300psi
Pressure 0.250MPa
Pressure 0.600MPa
Pressure 1.000MPa
Pressure 1.600MPa
Vacuum 3in/762mm
BACK SAVE
6(16257<3(
3UHVVXUH3VL3VL3VL3VL3VL03D0SD03D03D
9DFXXPLQPP 'HIDXOWSVL
Hold Button: MENU/<System Startup>/..../Sensor Type
 7KH%&36FDQDFFHSWDYDULHW\RISUHVVXUHRUYDFXXPWUDQVGXFHUV7KLVRSWLRQZLOO
DOORZWKH%&36WRXWLOL]HWKHSURSHUVHQVRUGDWDEDVHGRQWKH6HQVRU7\SHVHOHFWHG
',63/$<67$1'$5'
(QJOLVKPHWULF 'HIDXOW(QJOLVK
Hold Button: MENU/<System Startup>/..../Display Standard
 7KH%&36FDQFRQWUROERLOHUVLQVWHDPKHDWLQJHQYLURQPHQW,WJLYHVWKHXVHUWKH
capability of displaying pressure and temperature information in either of the standards.
-DISPLAY STANDARD-
English
Metric
BACK SAVE
6(77,1*7+((066(732,176$9$,/$%/(,102'21/<
Hold Button: MENU/<System Startup>/..../EMS 4mA Set Point/EMS 20mA Set Point
 ,I(06P$LVVHOHFWHGIURPWKH&RQWURO0RGH0HQXDVWKHSUHVVXUHVHWSRLQW
VRXUFHWKHXVHUPXVWSXUFKDVHD:HLO0F/DLQ02',QWHUIDFHWR
accept the 4-20mA signal and transmit it to the BCP-8S.
 ,QDGGLWLRQWKHXVHUZLOOQHHGWRVHWWKHSUHVVXUHUDQJHSDUDPHWHUVLQWKH6WDUWXS0HQX
First, set the pressure reading at 4mA, then the set it at 20mA.
 7KH%&36ZLOORQO\UHDGWKHSUHVVXUHUDQJHEHWZHHQP$DQGP$EDVHGRQWKH
4mA and 20mA settings entered.
EMS 4mA SET POINT
0psi
[ ]
BACK SAVE
EMS 20mA SET POINT
100psi
[ ]
BACK SAVE
 7RVKXWGRZQWKHFRQWUROXVLQJWKH(06VLJQDOVHQGDVLJQDOWKDWLVDERYHRUEHORZWKH
2-22mA range. The display will show the message "Shutdown by EMS" and all
VWDJHVZLOOGHHQHUJL]H+RZHYHUWKH6\VWHPDQG&RPE$LUUHOD\VZLOOFRQWLQXHIRUWKH
5XQ2QGHOD\SHULRGWKHQGHHQHUJL]H
$/(57
A good practice after performing any Startup menu
PRGL¿FDWLRQVLVWRFKHFNDOORSHUDWLQJVHWWLQJVDQG
adjustments to match the new settings.
 previous next