Wayne-Dalton 9100 Door User Manual


 
18
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your
local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com
Tools Needed:
INSTALLATION WITH U-BAR
INSTALLATION WITH U-BAR
Power Drill
7/16” Socket
Driver
Vice Clamps
Phillips Head
Screwdriver
TOP SECTION
WITH OR
WITHOUT U-BAR
CENTER
LINE
OPERATOR
BRACKET
U-BAR
TOP
SECTION
TOP
FLANGE
(2) #12 X 1/2”
PHILLIPS HEAD
SCREWS
VICE CLAMP
NOTE: NOT REQUIRED FOR J-STRUTS.
OPERATOR BRACKET
Operator Bracket
NOTE: Operator bracket must be mounted
and secured prior to installing top section.
NOTE: If an idrive
TM
operator is to be
installed, the operator bracket is not
required to be installed.
IMPORTANT: WHEN INSTALLING A
TROLLEY TYPE OPERATOR ON 9100, 9400
AND 9600 SERIES DOORS, A WAYNE-
DALTON TROLLEY BRACKET MUST
BE SECURELY ATTACHED TO THE TOP
SECTION, ALONG WITH ANY U-BAR’S
INITIALLY PROVIDED WITH THE DOOR. IT IS
THEN UNNECESSARY TO FURTHER
REINFORCE THE TOP SECTION OF THIS
WAYNE-DALTON DOOR WHEN ATTACHING
A TROLLEY TYPE OPERATOR, AS LONG AS
THE INSTALLATION OF THE OPERATOR IS
ACCORDING TO WAYNE-DALTON’S
INSTRUCTIONS AND FORCE SETTINGS ARE
ADJUSTED PROPERLY.
Locate the center of the top section and
place the operator bracket on top of the
section as illustrated. Align the center of
the bracket with the center line of the
top section. For retro fit applications, the
operator bracket must be aligned with an
existing operator and positioned on the top
section as illustrated.
Install (2) #12 x 1/2” phillips head screws
on the top flange of the operator bracket.
U-BAR INSTALLED: If a U-Bar is installed
on the top section, clamp the bottom flange
of the operator bracket to the U-Bar. Make
sure the bottom flange of the bracket
is held in place, flush against the U-Bar
before continuing.
NO U-BAR INSTALLED: If a U-Bar is not
installed on the top section, continue with
the steps below.
Attach (4) 1/4”- 14 x 5/8” self tapping
screws to the front of the operator bracket.
Next attach (2) 1/4”- 14 x 5/8” self tapping
screws to the bottom flange of the operator
bracket. Remove vice clamps if placed on
operator bracket previously.
NOTE: If you have a 9100 door, use (2)
1/4”- 20 x 11/16” self drilling screws
used to attach the U-Bar instead of the (2)
1/4”- 14 x 5/8” self tapping screws when
attaching the bottom flange of the operator
bracket to U-Bar.
NOTE: When attaching an operator bracket
to the top section with a U-Bar installed,
apply additional pressure to thread the
fasteners into the U-Bar.
OPERATOR
BRACKET
(2) 1/4”- 14 X 5/8”
SELF TAPPING SCREWS
(4) 1/4”- 14 X 5/8”
SELF TAPPING
SCREWS
OPERATOR
BRACKET
OPERATOR
BRACKET
(6) 1/4”- 14 X 5/8”
SELF TAPPING
SCREWS
U-BAR
U-BAR
U-BAR
FRONT
BOTTOM
FLANGE
TOP
FLANGE
BOTTOM
FLANGE
BOTTOM
FLANGE
FRONT
TOP FLANGE INSTALLATION
INSTALLATION WITH U-BAR
INSTALLATION WITHOUT U-BAR
10