Filter
Top Products
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer,
refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com
Top section
Top
section
Nail
Door width
+ 3-3/8” to 3-1/2”
1-11/16”
to 1-3/4”
Flag
angle
Flag angle
Vertical track
against track rollers
Horizontal Tracks/Q.I Flag Angles
Tools: Ratchet wrench, 9/16” Socket, 9/16” Wrench, level, Step ladder
15
NOTE: If you have Quick Install flag angles, complete this step.
To install horizontal track, place the top rail end over the top track roller of the top section.
Align key slot of the bottom rail end of horizontal track with the Quick Install tab of the flag
angle. Push curved portion of horizontal track down to lock in place.
WARNING WARNING
DO NOT RAISE DOOR UNTIL HORIZONTAL TRACKS ARE SECURED AT REAR,
AS OUTLINED IN STEP, REAR BACK HANGS, OR DOOR COULD FALL FROM
OVERHEAD POSITION CAUSING SEVERE OR FATAL INJURY.
Level the horizontal track assembly and bolt the top rail of the horizontal track to the encoun-
tered slot in the flag angle using (1) 1/4”-20 x 9/16” track bolt, (1) 1/4”-20 flange hex nut
and (1) 5/16 washer. Repeat for other side.
Remove the nail that was temporarily holding the top section in place, installed in step, Top
Section.
IMPORTANT: FAILURE TO REMOVE NAIL BEFORE ATTEMPTING TO RAISE DOOR COULD
CAUSE PERMANENT DAMAGE TO TOP SECTION.
NOTE: If an idrive
®
opener will be installed, position horizontal tracks slightly above level.
Bottom rail
of horizontal
track
Flag angle
Quick
Install
tab
Key slot
Quick Install
tab in place
Tracks flush
1/4”-20
Flange hex
nut
Top rail of
horizontal
track
1/4”-20 x 9/16”
Track bolt
Washer
Flagangle
Vertical
track
Vertical
track
Horizontal Tracks/F.A. Flag Angles
Tools: Ratchet wrench, 7/16” Socket, 9/16” Socket, 9/16” Wrench,
level, Step ladder, Flat tip screwdriver
16
NOTE: If you have Fully Adjustable flag angles, complete this step.
To install horizontal track, place the top rail end over the top track roller of the top section.
Align the bottom rail end of the horizontal track with the top of the vertical track. If you have
Quick Install horizontal track, tighten the bottom rail of the horizontal track to the flag angle
with (1) stud plate and (2) 1/4”-20 flange hex nuts. If you have Universal horizontal track,
tighten the bottom rail of the horizontal track to the flag angle with (2) 1/4”-20 x 9/16” track
bolts and (2) 1/4”-20 flange hex nuts.
WARNING WARNING
DO NOT RAISE DOOR UNTIL HORIZONTAL TRACKS ARE SECURED AT REAR,
AS OUTLINED IN STEP, REAR BACK HANGS, OR DOOR COULD FALL FROM
OVERHEAD POSITION CAUSING SEVERE OR FATAL INJURY.
Level the horizontal track assembly and bolt the top rail of the horizontal track to the encoun-
tered slot in the flag angle using (1) 1/4”-20 x 9/16” track bolt, (1) 1/4”-20 flange hex nut
and (1) 5/16 washer. Repeat for other side.
Remove the nail that was temporarily holding the top section in place, installed in step, Top
Section.
IMPORTANT: FAILURE TO REMOVE NAIL BEFORE ATTEMPTING TO RAISE DOOR COULD
CAUSE PERMANENT DAMAGE TO TOP SECTION.
NOTE: If an idrive
®
opener will be installed, position horizontal tracks slightly above level.
Bottom rail
Quick Install
Horizontal
track
1/4”-20
Flange hex
nuts
Stud plate
Flag angle
upper slot
1/4”-20 x 9/16” Track bolts
Bottom rail Fully
Adjustable
Horizontal
track
1/4”-20
Flange hex
nuts
Flag angle
upper slot
1/4”-20
Flange hex
nut
Top rail of
horizontal
track
1/4”-20 x 9/16”
Track bolt
Washer
Flagangle
Vertical
track
Vertical
track
Adjusting Top Fixtures
Tools: 7/16” Wrench, Step ladder
17
With horizontal tracks installed, you can now adjust the LHR top brackets.
NOTE: Depending on your application, you may need to reverse the top bracket slide for
more adjustment, if needed, prior to securing it to the top bracket base.
TO ADJUST THE TOP BRACKET SLIDES: Loosen the (2) 1/4”-20 flange hex nuts (if neces-
sary) and vertically align the top section of the door with the lower sections. Once aligned,
position the top bracket slide, out against the horizontal track. Maintaining the slide’s posi-
tion, tighten the (2) 1/4”-20 flange hex nuts to secure the top bracket slide to the top bracket
base. Repeat for other side.
TO REVERSE THE TOP BRACKET SLIDES (IF NEEDED): Remove the two 1/4” - 20 x 5/8”
carriage bolts, two retention washers and two 1/4” - 20 flanged hex nuts. Flip the top bracket
slide in the opposite direction. Loosely fasten the top bracket slide to the bracket using two
1/4” - 20 x 5/8” carriage bolts, two retention washers and two 1/4” - 20 flanged hex nuts,
as shown.
NOTE: The retention washers must be fully seated against the top bracket base to ensure the
anti-twist feature on the top bracket slide engages in the slotted hole in the top bracket base.
(2) 1/4” - 20
Flange hex nuts
Top section
Low headroom
horizontal track
Roller
Top bracket
assembly
Top bracket
slide
(2) 1/4” - 20
Flange hex nuts
(2) Retention washers
Top bracket slide
Top bracket
slide reversed
Slotted hole of top
bracket base
Anti-twist
feature
(2) 1/4” - 20 x 5/8”
Carriage bolts
End Bearing Brackets
Tools: Step ladder, Power drill, 7/16” Socket driver
18
NOTE: Right and left hand is always determined from inside the garage looking out.
End bearing brackets are right and left hand. Align the bottom edge of left end bearing
bracket with the top edge of the flag angle. Maintaining this alignment, also align the right
edge of the end bearing bracket with the right edge of the flag angle.
Secure the end bearing bracket to the jamb using (3) 5/16” x 1-5/8” lag screws, as shown.
Repeat same process for the other side.
10