Superior DT-400CMN Indoor Fireplace User Manual


 
26
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
SIT Millivolt Gas Valve
Pressure
Regulator
Remove
These
Components
Figure 59
Step 4. Millivolt Appliances - SIT Systems
a. See
Figure 59
and the instructions provided
with the kit. Using a Torx T20, remove and
discard the three pressure regulator mounting
screws. Remove the pressure regulator, spring,
poppet, diaphragm and bushing. Discard all
removed components. Ensure the rubber gas-
ket installed on the back of the replacement
pressure regulator is properly positioned and
install the new pressure regulator using the
new screws supplied with the kit. Tighten
screws to 25 In. lb. torque.
GAS CONVERSION KITS
WARNING: THIS CONVERSION KIT SHALL BE
INSTALLED BY A QUALIFIED SERVICE AGENCY IN
ACCORDANCE WITH THE MANUFACTURER'S IN-
STRUCTIONS AND ALL APPLICABLE CODES AND
REQUIREMENTS OF THE AUTHORIZED AGENCY
HAVING JURISDICTION. IF THE INFORMATION IN
THESE INSTRUCTIONS IS NOT FOLLOWED EX-
ACTLY, A FIRE, EXPLOSION OR PRODUCTION OF
CARBON MONOXIDE MAY RESULT CAUSING
PROPERTY DAMAGE, PERSONAL INJURY OR LOSS
OF LIFE. THE INSTALLATION IS NOT PROPER AND
COMPLETE UNTIL THE OPERATION OF THE CON-
VERTED APPLIANCE IS CHECKED AS SPECIFIED IN
THE OWNER INSTRUCTIONS SUPPLIED WITH THE
KIT. THE QUALIFIED SERVICE AGENCY PERFORM-
ING THIS INSTALLATION ASSUMES RESPONSI-
BILITY FOR THIS CONVERSION.
AVERTISSEMENT: CET ÉQUIPEMENT DE CONVERSION
SERA INSTALLÉ PAR UNE AGENCE QUALIFIÉE DE SERVICE
CONFORMÉMENT AUX INSTRUCTIONS DU FABRICANT ET
TOUTES EXIGENCES ET CODES APPLICABLES DE
L'AUTORISÉS AVOIR LA JURIDICTION. SI L'INFORMATION
DANS CETTE INSTRUCTION N'EST PAS SUIVIE
EXACTEMENT, UN FEU, EXPLOSION OU PRODUCTION DE
PROTOXYDE DE CARBONE PEUT RÉSULTER LE DOMMAGES
CAUSER DE PROPRIÉTÉ, PERTE OU BLESSURE
PERSONNELLE DE VIE. L'AGENCE QUALIFIÉE DE SERVICE
EST ESPONSABLE DE L'INSTALLATION PROPRE DE CET
ÉQUIPMENT. L'INSTALLATION N'EST PAS PROPRE ET
COMPLÉTE JUSQU'À L'OPÉRATION DE L'APPAREIL
CONVERTI EST CHÉQUE SUIVANT LES CRITÈRES ÉTABLIS
DANS LES INSTRUCTIONS DE PROPRIÉTAIRE
PROVISIONNÉES AVEC L'ÉQUIPEMENT.
tiKnoisrevnoCsaGenaporPoTlarutaN
)smetsySllewyenoH(
.oNsledoMepyTtinU.oNgolataC
004-TDtlovillim15M62
004-RDtlovillim15M62
004-TDcinortcele09L99
004-RDcinortcele09L99
tiKnoisrevnoCsaGlarutaNotenaporP
)smetsySllewyenoH(
.oNledoMepyTtinU.oNgolataC
004-TDtlovillim55M62
004-RDtlovillim55M62
004-TDcinortcele19L99
004-RDcinortcele19L99
tiKnoisrevnoCsaGenaporPoTlarutaN
)smetsySTIS(
.oNsledoMepyTtinU.oNgolataC
004-TDtlovillim4951H
004-RDtlovillim4951H
004-TDcinortcele09L99
004-RDcinortcele09L99
tiKnoisrevnoCsaGlarutaNotenaporP
)smetsySTIS(
.oNledoMepyTtinU.oNgolataC
004-TDtlovillim5951H
004-RDtlovillim5951H
004-TDcinortcele19L99
004-RDcinortcele19L99
In Canada:
THE CONVERSION SHALL BE CARRIED OUT
IN ACCORDANCE WITH THE REQUIREMENTS
OF THE PROVINCIAL AUTHORITIES HAVING
JURISDICTION AND IN ACCORDANCE WITH
THE REQUIREMENTS OF THE CAN1-B149.1
AND .2 INSTALLATION CODE.
LA CONVERSION DEVRA ÊTRE EFFECTUÉE
CONFORMÉMENT AUX RECOMMANDATIONS
DES AUTORITÉS PROVINCIALES AYANT
JURIDICTION ET CONFORMÉMENT AUX
EXIGENCES DU CODE D'INSTALLATION CAN1-
B149.1 ET.2.
Gas conversion kits are available to adapt your
appliance from the use of one type of gas to the
use of another. These kits contain all the neces-
sary components needed to complete the task
including labeling that must be affixed to en-
sure safe operation.
Kit part numbers are listed here and the follow-
ing steps detail the conversion procedure.
Step 1. Turn off the gas supply to the appliance.
Remove the front glass door/frame from the
appliance. Access the control compartment.
Step 2. Carefully remove the logs.
Exercise
care as not to break the logs.
Step 3. Locate the screws securing the burner
(tray) to the appliance. Remove the burner and
retain the securing screws.