Superior BR-36-2 Indoor Fireplace User Manual


 
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
12
The offset and return elbows may be attached
together, or a section or sections of chimney
may be used between, but do not exceed 20' in
total length between elbows. If sections of pipe
exceed 10' between elbows, a chimney stabi-
lizer must be used at the midpoint (
Figure 36
).
The stabilizer support straps must be attached
under tension (in shear) to structural framing
members above. When two sets of elbows are
used, the maximum combined length of chim-
ney used between elbows cannot exceed 20'
(
Figure 37
). Example: If C
1
= 10' then C
2
cannot
exceed 10'.
If an offset exceeds 6' in length, each chimney
joint beyond the first 6' of offset to the return
elbow, must be secured by a No. 8 x 1/2" sheet
metal screw located at the underside of the joint
(
Figure 38
).
A 1/8" diameter hole must be drilled in the
chimney joint using a 1/8" diameter drill. Hole
should be drilled in center of joint overlap
(
Figure 39
). Be sure to drill only through the
outer chimney casting. Do not puncture the
inner flue.
Maximum offset of chimney system is 30°. Two
offsets must not be assembled to form a 60°
offset. However, two sets of offset and return
elbows may be used on a single flue system,
provided the total height of the system exceeds
25'.
Return elbow support straps must be securely
attached under tension (in shear) to structural
framing members above. Do not substitute a
FTF8-30 offset elbow in place of a FTF8-E30
return elbow.
OFFSET CALCULATIONS
Step 1. Use Offset Chart to determine amount
of horizontal offset (A) and height (B) for vari-
ous chimney section assemblies.
Step 2. Use “Height of Chimney Only” column
in The Vertical Elevation Chart to determine
combinations of chimney used above return
elbow to achieve desired heights. Reference
Components Effective Height Chart in vertical
elevation chart section.
Step 3. Use Elevation Chart as job estimator
only. Add necessary firestop spacers and stabi-
lizers as required. Firestop spacers must be
used as shown in
Figures 22 and 23
and stabi-
lizers as shown in
Figure 28
.
FTF8 VERTICAL ELEVATION CHART
Height Of Number Of FTF8
Chimney Only Chimney Lengths
Inches Feet/Inches 12" 18" 36" 48"
Height Of Number Of FTF8
Chimney Only Chimney Lengths
Inches Feet/Inches 12" 18" 36" 48"
386 ¹⁄₂ 32 2 ¹⁄₂ 0108
390 ³⁄₄ 32 6 ³⁄₄ 2008
396 ³⁄₄ 33 0 ³⁄₄ 1108
404 ¹⁄₂ 33 8 ¹⁄₂ 0018
414 ³⁄₄ 34 6 ³⁄₄ 1018
416 ¹⁄₂ 34 8 ¹⁄₂ 0009
420 ³⁄₄ 35 0 ³⁄₄ 0118
426 ³⁄₄ 35 6 ³⁄₄ 1009
432 ³⁄₄ 36 0 ³⁄₄ 0109
437 36 5 2 0 0 9
443 36 11 1 1 0 9
450 ³⁄₄ 37 6 ³⁄₄ 0019
461 38 5 1 0 1 9
462 ³⁄₄ 38 6 ³⁄₄ 00010
466 ³⁄₄ 38 10 ³⁄₄ 0119
472 ³⁄₄ 39 4³⁄₄ 10010
478 ³⁄₄ 39 10 ³⁄₄ 01010
483 40 3 2 0 0 10
489 40 9 1 1 0 10
496 ³⁄₄ 41 4 ³⁄₄ 00110
507 42 3 1 0 1 10
508 ³⁄₄ 42 4 ³⁄₄ 00011
513 42 9 0 1 1 10
519 43 3 1 0 0 11
525 43 9 0 1 0 11
529 ¹⁄₄ 44 1 ¹⁄₄ 20011
535 ¹⁄₄ 44 7 ¹⁄₄ 11011
543 45 3 0 0 1 11
553 ¹⁄₄ 46 1 ¹⁄₄ 10111
555 46 3 0 0 0 12
559 ¹⁄₄ 46 7 ¹⁄₄ 01111
565 ¹⁄₄ 47 1 ¹⁄₄ 10012
571 ¹⁄₄ 47 5 ¹⁄₄ 01012
575 ¹⁄₂ 47 11 ¹⁄₂ 20012
581 ¹⁄₂ 48 5 ¹⁄₂ 11012
589 ¹⁄₄ 49 1 ¹⁄₄ 00112
599 ¹⁄₂ 49 11 ¹⁄₂ 10112
601 ¹⁄₄ 50 1 ¹⁄₄ 00013
605 ¹⁄₂ 50 5 ¹⁄₂ 01112
611 ¹⁄₂ 51 11 ¹⁄₂ 10013
617 ¹⁄₂ 51 5 ¹⁄₂ 01013
621 ¹⁄₂ 51 9 ¹⁄₂ 20013
627 ¹⁄₂ 52 3 ¹⁄₂ 11013
635 ¹⁄₂ 52 11 ¹⁄₂ 00113
645 ¹⁄₂ 53 9 ¹⁄₂ 10113
647 ¹⁄₂ 53 11 ¹⁄₂ 00014
651 ¹⁄₂ 54 3 ¹⁄₂ 01113
657 ¹⁄₂ 54 9 ¹⁄₂ 10014
663 ¹⁄₂ 55 3 ¹⁄₂ 01014
667 ³⁄₄ 55 7 ³⁄₄ 20014
673 ³⁄₄ 56 1 ³⁄₄ 11014
681 ¹⁄₂ 56 9 ¹⁄₂ 00114
691 ³⁄₄ 57 7 ³⁄₄ 10114
693 ¹⁄₂ 57 9 ¹⁄₂ 00015
697 ³⁄₄ 58 1 ³⁄₄ 01114
703 ³⁄₄ 58 7 ³⁄₄ 10015
709 ³⁄₄ 59 1 ³⁄₄ 01015
714 59 6 2 0 0 15
720 60 0 1 1 0 15
727 ³⁄₄ 60 7 ³⁄₄ 00115
738 61 6 1 0 1 15
739 ³⁄₄ 61 7 ³⁄₄ 00016
744 62 0 0 1 1 15
11 0 11 1 0 0 0
17 1 5 0 1 0 0
21 ¹⁄₄ 19¹⁄₄ 2000
27 ¹⁄₄ 23¹⁄₄ 1100
35 2 11 0 0 1 0
47 3 11 0 0 0 1
51 ¹⁄₄ 43¹⁄₄ 0110
57 ¹⁄₄ 49¹⁄₄ 1001
63 ¹⁄₄ 53¹⁄₄ 0101
67 ¹⁄₄ 57¹⁄₄ 2001
73 ¹⁄₄ 61¹⁄₄ 1101
81 ¹⁄₄ 69¹⁄₄ 0011
93 ¹⁄₄ 79¹⁄₄ 0002
97 ¹⁄₄ 81¹⁄₄ 0111
102 ¹⁄₂ 86¹⁄₂ 1002
109 ¹⁄₄ 91¹⁄₄ 0102
113 ¹⁄₂ 95¹⁄₂ 2002
119 ¹⁄₂ 911¹⁄₂ 1102
127 ¹⁄₄ 10 7 ¹⁄₄ 0012
137 ¹⁄₂ 11 5 ¹⁄₂ 1012
139 ¹⁄₄ 11 7 ¹⁄₄ 0003
143 ¹⁄₂ 11 11 ¹⁄₂ 0112
149 ¹⁄₂ 12 5 ¹⁄₂ 1003
155 ¹⁄₂ 12 11 ¹⁄₂ 0103
159 ³⁄₄ 13 3 ³⁄₄ 2003
165 ³⁄₄ 13 9 ³⁄₄ 1103
173 ¹⁄₂ 14 5 ¹⁄₂ 0013
183 ³⁄₄ 15 3 ³⁄₄ 1013
185 ¹⁄₂ 15 5 ¹⁄₂ 0004
189 ³⁄₄ 15 9 ³⁄₄ 0113
195 ³⁄₄ 16 3 ³⁄₄ 1004
201 ³⁄₄ 16 9 ³⁄₄ 0104
206 17 2 2 0 0 4
212 17 8 1 1 0 4
219 ³⁄₄ 18 3 ³⁄₄ 0014
230 19 2 1 0 1 4
231 ³⁄₄ 19 3 ³⁄₄ 0005
236 19 8 0 1 1 4
242 20 2 1 0 0 5
248 20 8 0 1 0 5
252 21 0 2 0 0 5
258 21 6 1 1 0 5
266 22 2 0 0 1 5
276 23 0 1 0 1 5
278 23 2 0 0 0 6
282 23 6 0 1 1 5
288 24 0 1 0 0 6
294 ³⁄₄ 24 6 ³⁄₄ 0106
298 ¹⁄₄ 24 10 ¹⁄₄ 2006
304 ¹⁄₄ 25 4 ¹⁄₄ 1106
312 26 0 0 0 1 6
322 ¹⁄₄ 26 10 ¹⁄₄ 1016
324 27 0 0 0 0 7
328 ¹⁄₄ 27 4 ¹⁄₄ 0116
334 ¹⁄₄ 27 10 ¹⁄₄ 1007
340 ¹⁄₄ 28 4 ¹⁄₄ 0107
344 ¹⁄₂ 28 8 ¹⁄₂ 2007
350 ¹⁄₂ 29 2 ¹⁄₂ 1107
358 ¹⁄₄ 29 10 ¹⁄₄ 0017
368 ¹⁄₂ 30 8 ¹⁄₂ 1017
370 ¹⁄₄ 30 10 ¹⁄₄ 0008
374 ¹⁄₂ 31 2 ¹⁄₂ 0117
380 ¹⁄₂ 31 8 ¹⁄₂ 1008