Filter
Top Products
NOTE: if your garage has a built up jamb, drill the hole
2" deep. Then, on inside edge of jamb, drill a second hole
into first hole to complete access_
l/8" Pilot Hole I _'_--_
"4 1"V.i,--..__'_. fjfq.....
1" Dia Hole N \,J,_\"_
t_._"-_JIr I 1 1J I1_", I CabLe
Screw I I IL!III!IM
ooo, --_ I I I IIit tl rlnsi,deEdge
STEP 2: Hold keyboard firmly with the back of the case UP.
Position thumb against bottom of case and pull up sharply
Keyboard will lift out of cover, allowing access to bottom
mounting hole
Guide the keyboard cable through hole to inside of garage.
Position the keyboard against outside jamb Drill two 1/8" pilot
holes for fastening screws Attach securely with (2) 6ABx1-1/4"
screws CIose cover
Excess cable can be folded and inserted into the access ho_e
to keep it out of the way
Bell Wife
Transformer (To Garage
TerminaJs Doer Opener)
Con ne,;,"l_Or
Guides
Kit
4'_A3468 Cable
To 120V Ou#et
STEP 3: Connect the 2-strand bell wire to terminals labeled
1 and 2 on back of console, insert keyboard cable connector
into slot on side of console Be sum connector guides are
facing BACK of consote.
IMPORTANT; Some garage door openers have a third
screw terminal which supplies power to the radio control.
This terminal can be connected to terminal No. 3 on the
console with a third strand of bell wire (not supplied).
With any garage door opener made by Stanley, accessory
transformer kit 41A3468 MUST be installed.
TRANSFORMER INSTALLATION INSTRUCTIONS: Connect
one end of the 2-strand bell wire supplied with the kit to each
of the transformer terminals Polarity is not imporlant Con-
nect the other end of bell wire to terminals 1 and 3 on the
Touch Code console.
IF THIS ACCESSORY IS USED WITH ANY GARAGE DOOR
OPENER OTHER THAN SEARS OR CHAMBERLAIN AND
THE BATTERY FAILS IN TWO MONTHS, TRANSFORMER
MUST BE INSTALLED° Follow instructions above.
STEP 4: Position console on an interior garage wall approxi-
mately one foot from outside edge of door. Fasten with (2)
8ABxl" screws
Run bell wire up wall and across ceiling to garage door opener
terminals Use insulated staples to secure wire Cut off any
excess wire Connect to terminals used for push button
controls
On Sears models, connect wire as follows:
Model series 53000--to red and white terminals
Model 664400-Lto blue and white terminals
Modei 664000--to red and black terminals.
All other models_to white and white terminals or to the
terminals used for wall push button
STEP 5: Pry open front panel of console with a coin or screw-
driver. Snap a 9 voIt battery onto circuit board connector and
drop into console DO NOT replace panel at this time
Console
Push Button
STEP 6: To set code, move programloperate switch near the
battery to PROGRAM position (keyboard light should flash)
NOTE: If the light does not flash, check the cable and bat-
tery connections° Press any four numbers on keyboard
CAUTION: For security, do not use address, license or
consecutive numbers (1,2,3,4 etc.).
Move the programloperate switch toOPERATE position (the
keyboard light will go off)
Reconnect power to garage door opener If you have installed
Transformer Kit 41A3468, plug the transformer into a 120
Volt outlet. Enter the code on the keyboard. If the door oper-
ates properfy, replace the front panet on the console
Loss of power to either the battery or the garage door opener
will not affect the programmed code. However, if BOTH lose
power, the code must be reseL
Battery should produce adequate power for at least one year_
If light in keyboard does not turn on, change the battery.
NOTE: To maintain the privacy of your code, keep all of
the buttons free from soU° If any of the numbers show
signs of wear, change your code°
114Al136 Stde 2 Printed In Mexico