Filter
Top Products
Water heater(s) shall be model ________________, manufactured by RHEEM-RUUD, having electrical input of __________
kW and a recovery rate of _____________ GPH at a 100°F temperature rise. Water heater(s) shall have a storage capacity of
___________ gallons. Water heater(s) shall have the UL seal of certification and be factory equipped with an AGA/ASME rated
temperature and pressure relief valve. Tank(s) shall have a double coating of high temperature porcelain enamel and furnished
with magnesium anode rods rigidly supported. Water heater(s) shall meet or exceed the standby loss requirements of
ASHRAE Standard 90.1b-2001. Tank(s) shall have a working pressure of 150 psi, and shall be completely assembled. Water
heater(s) shall be approved-listed and constructed in accordance with UL Sanitation (NSF5). Water heater(s) shall be equipped
with LIFEGUARD “screw-in” type elements featuring a stainless steel outer sheath of INCO-LOY 840 material. Tank shall be
insulated with 3" of rigid polyurethane foam insulation. Water heater(s) shall be constructed with a SYSTEM SENTINEL
element diagnostic panel utilizing light emitting diodes. Each LED will correspond to the number and location of the heating
elements and monitor their on-off function. Water heater(s) shall be provided with internal power circuit fusing, control circuit
fusing, magnetic contactors, 120 volt control circuit transformer and surface mounted thermostat or immersion thermostat(s)
with manual reset high limit control. 1-1/2" inlet and outlet water connections shall be provided. Water heater(s) shall be
covered by a three year limited warranty against tank leaks.
Add for ASME construction
Water heater(s) shall be constructed in accordance with the requirements of the ASME Boiler and Pressure Vessel Code,
Section IV Part HLW.
This product features a three year limited warranty against tank leaks. Please refer to Commercial Warranty Information
brochure for complete warranty information.
Recommended Specifications:
Limited Warranty:
COMMERCIAL
WATER HEATERS
Rheem Water Heating • 101 Bell Road, Montgomery, Alabama 36117-4305 • www.rheem.com
Rheem Canada Ltd./Ltée,128 Barton Street West, Hamilton, Ontario L8N 3P3
PRINTED IN U.S.A 02/06 WP FORM NO. RR102CE-1 Rev. 12
In keeping with its policy of continuous progress and product improvement, Rheem-Ruud reserves the right to make changes without notice.
Heavy Duty Electric continued.
Other Features:
• Integral Fusing –
all models have integral fusing for each element.
• Anode Rods –
two (2) magnesium anodes are installed in each tank
to ensure long life and corrosion resistance.
• Temperature and Pressure Relief Valve –
AGA/ASME rated and factory installed.
• Electrical Connections –
pre-wired, accessible control box with multiple knock-
outs on side in size selections to match the National
Electric Code. Sizes range from 1/2" to 2". A ground-
ing screw is provided for attaching an equipment
grounding conductor.
• Single Panel Control Box –
with hinged door, provides immediate access to all
electrical components and elements.
• Terminal Block –
all models are equipped with U.L. listed terminal
blocks for simplicity of installation. The terminal
block will accept either copper or aluminum field
connect wire.
• 120 Volt Control Circuit –
all units are furnished with a fused 120 volt control
circuit. All controls (thermostats, high temperature
limit, etc.) are operated off of this basic 120 volt
control circuit. This circuit is created by an internal
multi-tap transformer of unique design that has four
(4) taps for the primary voltages, 208, 240, 277
and 480.
• Water Connections –
hot outlet and cold inlet are 1-1/2" NPT dielectric
nipples which prevent excessive turbulence of heated
water and results in optimum tank draw.