Filter
Top Products
'Fasten the door to openingBYDRIVINGGALVANIZEDROOlNGNAILSINTOEACH
PREPUNCHEDHOLEINTHENAILINGlN
Note: Make sure the fin corner is lying as flat as possible. When using
the optional fin at the sill, attach the aluminum sill support or wood
blocking under the sill of the door before proceeding to Step H.
( Carefully open the door(s) and remove all shipping spacers.
Note: Be sure to remove the spacers from the bottom edge of the door panel.
Double doors with center latch:
Designer Series Only: Use the construction handle to operate the active door
HANDLE/PERATETHEmUSHBOLTSPERTHEINSTRUCTIONSONTHELABELONTHESTRIKE
located on the astragal.
Architect Series Only: Use the construction handle to operate both the active
and passive door panels.
I. Out-swing doors: Place a dab of sealant in each of the pre-drilled holes in the bottom of the door frame, then insert a
XmATHEADCORROSIONRESISTANTWOODSCREWPROVIDEDINTOTHISHOLE
Note: Single doors will have two pre-drilled holes, double doors will have four.
)Out-swing double doors only:0LACEADABOFSEALANTINTOTHECENTERHOLEOFTHESTRIKEPLATELOCATEDATTHESILLOFTHEDOOR
)NSTALLAXmATHEADCORROSIONRESISTANTWOODSCREWPROVIDEDINTOTHISHOLE
Note: For masonry floors, use a #8 masonry screw instead of the wood screw.
J. On center latching (double) doors: Place shims at the top of the door frame above
THECENTERSTRIKEPLATE3ECURETHESHIMSBYINSERTINGAXmATHEADCORROSION
RESISTANTSCREWINTOTHEUPPERDOORFRAMETHROUGHTHECENTERHOLEOFTHESTRIKEPLATE
and the shims into the rough opening.
*On center hinged double doors: Insert and attach shims directly
above the astragal in the center of the unit.
Note: Step K does not apply to center hinged doors.
K. On each hinge, starting at the top, insert a 3" long screwPROVIDEDINTOTHE
OPENSCREWHOLE-AKESURETHATTHESCREWPASSESTHROUGHTHESHIMSANDINTOTHE
structural framing.
L. Check door operation./PENANDCLOSETHEDOORTOCHECKFORPROPEROPERATION
-AKESURETHEDOORWILLLATCHCORRECTLY
Note: If there are any problems with the operation, recheck and adjust the reveal.
M. Adjust the reveal if needed.
Architect Series and Designer Series only:4HEDOORPANELSHAVEADJUSTABLEHINGELEAFS5SINGAALLENWRENCH
TURNTHECENTERSCREWCLOCKWISETOINCREASETHESPACEBETWEENTHEHINGESIDEOFTHEFRAMEANDTHEDOORPANELORCOUNTER
CLOCKWISETOINCREASETHESPACEBETWEENTHEDOORPANELANDTHELOCKSIDEOFTHEFRAME$/./4TURNTHESCREWSMORE
THANTURNINEITHERDIRECTION)NSOMECASESITMAYBENECESSARYTOLOOSENANDTHENTIGHTENTHETOPANDBOTTOMHINGE
screws to obtain full hinge adjustment. If necessary, loosen the top and bottom screws, and immediately retighten them.
With the screws retightened, turn the adjustment hinge screw. If the hinge will not adjust any further then it is adjusted
as far as it will go. If more clearance is needed adjust the shims between the frame and the rough opening.
Note: DO NOT adjust the hinge with the top and bottom screws loose; this could force the hinge to adjust beyond
its design capability which can cause the hinge to bind, damage the hinge and/or pull out the screws. A 3/4 turn of
the center screw provides approximately 1/16" adjustment.
Note: For more issues with the adjustable strike latching, go to the troubleshooting section at the end of this instruction.
ProLine Series only: Plastic shims located behind the hinges may be removed to adjust the reveal between the door panel
and door frame. Additional hinge shims may be added if required.
N. On doors with a lock strike in the side,DRILLADIAMETERXDEEPPILOTHOLETHROUGHTHELOCKSTRIKEANDINTOTHE
ROUGHOPENING)NSERTAXCORROSIONRESISTANTSCREWPROVIDEDINTOTHEPILOTHOLEMAKINGSURETHATITPASSESTHROUGH
the shim and into the stud.
Note: This step does not apply to center latching double doors.
O. Install a #8 x 3" flat head corrosion resistant screwINTOTHEHOLELOCATEDAPPROXIMATELYFROMTHETOPOFTHE
door frame, on the latch side of the frame.
&YUFSJPS
Ó
Ó
*OUFSJPS
Ó
Ó
Ó
Ó