6
1 Press TIMER button.
2 Press ▼ button once.
“ ”
Æ
“ ”
3 Press SET button.
[EXAMPLE] “ ” flashes,
“
” lights.
4 Press ▲ or ▼ button.
The display changes as below. Set as you like.
“ ”
⇔
“ ” ~ “ ”
⇔
“ ”
5 Press SET button.
Sleep timer has been set.
If the Sleep timer is set when the unit stops, it starts operating.
After “ ” is displayed in the display area, it returns to
step 2.
<When “Ten hours later OFF” is set >
“ ” (lights)
“ ” (lights for two seconds)
È
“ ” (lights)
“
” (lights)
The time left is displayed by one hour as time passes off after the
setting.
When the setting time elapses, the unit stops operating.
The unit stops operating at each setting time once it is set.
6 Press ON/OFF button. The timer mode is
finished.
1 Press TIMER button.
2 Press ▼ button twice.
[ ]
Æ
[ ]
Æ
[ ]
3 Press SET button.
[EXAMPLE] “ ” flashes,
“ ” lights.
4 Press ▲ or ▼ button.
Set the time at which you want to stop the operation.
Set “Hour”•
If you press ▲ or ▼ button for a while, “Hour” display is changed
by one hour, and stops when you stop pressing.
Set “Minute”•
If you press ▲ or ▼ button, the display increases or decreases
by ten minutes.
5 Press SET button.
OFF timer has been set.
After “ ” is displayed in the display area, it returns
to step 2.
<If set to 6:00 PM >
“
” (lights)
“
” (lights for two seconds)
↓
“ ”(lights)
“ ” (lights)
The unit stops operating at 6:00 PM.
The time display is also turned off.
6 Press button. The timer mode is finished.
The unit stops operating at the setting time.
This setting is effective for only once.
If you start the operation while you are setting the OFF
timer, operate the air conditioner before setting of timer.
SLEEP TIMER MODE
OFF TIMER MODE
• If you press button while timer mode
is operative, timer mode is canceled and the
display will return to the original display.
•
If you do not press any button for several minutes
after entering the timer mode, the timer mode
ends and returns to the original display.
NOTE
• If you press button while timer mode
is operative, timer mode is canceled and the
display will return to the original display.
• If you do not press any button for several minutes
after entering the timer mode, the timer mode
ends and returns to the original display.
ATTENTION
After certain period has elapsed, the unit stops operating.
• Sleep timer
The unit stops operating at each setting time once it is set.
NOTICE
HOW TO PERFORM THE TIMER OPERATION < WIRED REMOTE CONTROL >
1 Press TIMER button.
It enters the timer mode.
“Current day of the week” and “Current time” are displayed.
Display area : [
]
[
]
[
]
2 Press SET button.
The display area shows : [ ]
(▼ flashes)
[
] (current time)
[
]
3 Press ▲ or ▼ button.
Align the ▼ mark above the day of the week to the current
day of the week.
Press ▲ and ▼ mark to move to the right and the left respectively.
If you press the RESET button, the remote control will return to
the previous screen and display “ ”.
4 Press SET button.
The day of the week is fixed, and the flashing of ▼ mark turns to
lighting stably.
“current time” is displayed by flashing in the ON timer display area,
and “ ” is displayed in the display area.
5 Press ▲ or ▼ button.
Set to the current time.
If you press the
RESET button, the remote controller return
to step 1.
6 Press SET button.
The flashing for time display turns to lighting stably, and
“ ” is displayed to show that the current time is set.
Two seconds later, it returns to step 1, and “ ” is
displayed.
7 Press button.
The timer mode is finished.
2 3 1
• •
4 5
•
6
7
Timer operation is performed base on the time set by the steps described in this section. Make sure to set the
time to the current time correctly.
SETTING THE TIME
•
If you press button while timer mode is operative,
timer mode is canceled and the display will return to the
original display. Note that the setting which has not been
completed is canceled.
•
If you do not press any button for several minutes after
entering the timer mode, the timer mode ends and returns
to the original display.
ATTENTION
