Mitsubishi Electronics MSZ12UN Air Conditioner User Manual


 
6
FAN
VANE
MODE
STOP
START
HR.
MIN.
I FEEL
COOL
DRY
RESET CLOCK
HEAT
PREPARATION BEFORE OPERATION
Breaker for the air conditioner
Turn the breaker on.
Handling of the remote controller
The range that the signal can reach is about
20 ft. when the remote controller is pointed at the
front of the indoor unit.
When a button is pressed, one or two beeps will
be heard from the indoor unit. If no sound is heard,
operate again.
Use the remote controller carefully.
If it is dropped, thrown or it gets wet, the remote
controller may not operate.
When installing on a wall, etc.
Install the remote controller holder in a position
where the signal reception sound (beep) can be
heard from the indoor unit when the
ON/OFF
button is
pressed.
How to install/remove the remote controller
Installing Insert the remote controller downward.
Removing Pull it up.
Dry-cell batteries
Reference for replacing batteries
When the indoor unit does not respond to the signal
from the remote controller, or the display becomes
dim, replace the batteries with new ones (size AAA).
Though both alkaline batteries and manganese
batteries can be used, alkaline batteries are rec-
ommended because their service life is longer than
that of manganese batteries.
The service life of an alkaline battery is about 1 year.
However, a battery which the time limit is ap-
proaching may be exhausted soon. The recom-
mended usable time limit is indicated (month/year)
on the bottom of the battery.
Replace the 2 batteries with new ones of the same
type.
Do not use rechargeable batteries.
To prevent liquid leakage, take out all batteries
when the remote controller is not going to be used
for a long time.
Dispose of exhausted batteries in the correct man-
ner.
Remote controller (How to set the batteries and the current time)
1
Remove the front lid and insert bat-
teries. Then reattach the front lid.
Insert the minus pole of the batteries first.
Check if the polarity of the batteries is correct.
2
Press the RESET button.
If the RESET button is not pressed, the remote control-
ler may not operate correctly.
3
Press the CLOCK set button.
4
Press the
HR.
and
MIN.
button
(TIME SET button) to set the current
time.
Each time the
HR.
button is pressed, the set time in-
creases by 1 hour, and each time the
MIN.
button is
pressed, the set time increases by 1 minute.
5
Press the CLOCK set button again
and close the front lid.
When the remote controller cannot
be used (emergency operation)
When the batteries of the remote controller run out or
the remote controller malfunctions, the emergency op-
eration can be done using the EMERGENCY OPERA-
TION switch.
1
Press the EMERGENCY OPERA-
TION switch.
* Each time the EMERGENCY OPERATION
switch is pressed, the unit will operate in order
of EMERGENCY COOL MODE, EMERGENCY
HEAT MODE and STOP MODE.
However, when the EMERGENCY OPERA-
TION switch is once pressed, the unit will oper-
ate in test run for 30 minutes and then the op-
eration mode shifts to EMERGENCY MODE.
MSZ09UN MSZ12UN
Details of EMERGENCY MODE are as shown below.
However, the temperature control does not work for 30
minutes in test run and the unit is set to continuous
operation. The fan speed is set to High in test run and
shifts to Medium after 30 minutes.
Operation mode COOL HEAT
Set temperature 75 °F 75 °F
Fan speed Medium Medium
Horizontal vane Auto Auto
The operation mode is indicated by the Operation Indi-
cator lamp on the indoor unit as following figures.
Operation Indicator lamp
MSZ09UN
EMERGENCY COOL EMERGENCY HEAT STOP
MSZ12UN
EMERGENCY COOL EMERGENCY HEAT STOP
To stop the emergency operation,
press the EMERGENCY OPERATION
switch once (in case of EMER-
GENCY HEAT MODE) or twice (in
case of EMERGENCY COOL MODE).
Press using
a thin stick.
Press using
a thin stick.
Remote controller
holder
Auto restart function
These models are equipped with an auto restart function. If you do not want to use
this function, please consult the service representative because the setting of the
unit needs to be changed.
Auto restart function is ...
When the indoor unit is controlled with the remote controller, the operation mode, the set temperature and
the fan speed are stored in the memory. If a power failure occurs or the main power is turned off during
operation, Auto restart function sets automatically to start operating in the same mode as the one set with
the remote controller just before the shutoff of the main power. (Refer to page 7 for details.)
Insert the minus
pole of the
batteries first.
Operation
Indicator
Operation
Indicator
Operation
Indicator
Operation IndicatorOperation IndicatorOperation Indicator