Filter
Top Products
4
ENGLISH
Explanation of general view
1 Battery cartridge
2 Push button
3Screw
4 Set plate
5Switch lever
6 Hook
7 Front lip
8 Cleaner body
9 Corner nozzle
10 Nozzle
11 Extension wand (Straight pipe)
SPECIFICATIONS
Model 4013D 4033D
Capacities ...................................................................................0.5 L 0.5 L
Continuous use (with battery 1222/1422) ...................................Approx.14min. Approx.14min.
Overall length ..............................................................................465mm 473 mm
Net weight ...................................................................................0.89 kg 0.89 kg
Rated voltage ..............................................................................D.C.12V D.C.14.4V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
ADDITIONAL SAFETY RULES
1. Read this instruction manual and the charger
instruction manual carafully before use.
2. Do not pick up wet materials, lit cigarettes or the
like.
3. Stop operation immediately if you notice any-
thing abnormal.
4. If you drop or strike the cleaner, check it care-
fully for cracks or damage before operation.
5. Do not bring close to stoves or other heat
sources.
6. Do not block the intake hole or vent holes.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing battery cartridge (Fig.1)
• Always switch off the cleaner before insertion or
removal of the battery cartridge.
• To remove the battery cartridge, withdraw it from the
cleaner while pressing the buttons on both sides of the
cartridge.
• To insert the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Always insert it all the way until it locks in
place with a little click. If not, it may accidentally fall out
of the cleaner, causing injury to you or someone
around you.
• Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
Installing set plate (optional accessory) for 4013D
only (Fig. 2)
Always install the set plate when using battery cartridges
1200, 1202 or 1202A. Install the set plate on the cleaner
with the screw provided.
Charging
Charge the battery cartridge with your Makita charger
properly before use.
Following batteries can be used for this cleaner;
Switch action (Fig.3)
CAUTION:
• Always be sure that the dust bag or paper filter is
installed properly in the cleaner before use. Improper
installation may allow dust to enter the motor, resulting
in malfunction of the cleaner.
• Always switch off the cleaner after each use to prevent
damage to the cleaner and to lengthen the service life
of the batteries.
To start the cleaner, slide the switch lever forward to the
“ I ” position.
To stop the cleaner, slide the switch lever back to the
“ O ” position.
Dust disposal
CAUTION:
Empty the cleaner before it becomes too full, or the suc-
tion force weakens.
Depress the buttons and open the front cover. (Fig.4)
Take the dust bag out of the cleaner carefully so that the
contents will not spill out. Empty the contents out of the
dust bag. (Fig.5)
Also empty out the dust inside the cleaner itself. Failure
to do so may cause the sponge filter to be clogged or the
motor to be damaged. (Fig.6)
Model Battery type
Capacity
(mAh)
Number of
cells
4013D
1200, 1220 1300 10
1202, 1222, 1202A 2000 10
1234 2600 10
1235, 1235A 3000 10
4033D
1420 1300 12
1422 2000 12
1434 2600 12
1435 3000 12