Filter
Top Products
• Set the mode switch to HEAT to program the
unit for controlling your heater. Set the mode
switch to COOL to program the unit for controlling
your air conditioner.
• Touch
MENU
.
• Use
SCROLL
to advance to SET/REVIEW HEAT
PROGRAMS or SET/REVIEW COOL PROGRAMS.
• Touch
YES
to begin scrolling through the HEAT
or COOL settings.
• Use the
UP/DOWN ARROW
to change the
flashing start time for MON MORN. One period
ends at the start time of the next period. The
beginning of a period may not be any closer to the
beginning of the next period than one 15 minute
increment.
• Touch
YES
to accept the displayed start time
and advance to program its set temperature.
• Use
UP/DOWN ARROW
to change the flashing
temperature setting for MON MORN.
• Touch
YES
to accept the displayed temperature
and advance to Set MON DAY start time.
• Use the
UP/DOWN ARROW
to change the
flashing start time for MON DAY.
• Touch
YES
to accept the displayed value and
advance to program temperature.
• Use
UP/DOWN ARROW
to change the flashing
temperature setting for MON DAY.
• Touch
YES
to accept the displayed temperature
and advance to Set MON EVE start time.
• Use the
UP/DOWN ARROW
to change the
flashing start time for MON EVE.
• Touch
YES
to accept the displayed value and
advance to program temperature.
• Use
UP/DOWN ARROW
to change the flashing
temperature setting for MON EVE.
• Touch
YES
to accept the displayed temperature
and advance to Set MON NITE start time.
• Use the
UP/DOWN ARROW
to change the
flashing start time for MON NITE.
• Touch
YES
to accept the displayed value and
advance to program temperature.
• Use
UP/DOWN ARROW
to change the flashing
temperature setting for MON NITE.
• Touch
YES
to accept the displayed temperature
and advance to Set TUE MORN start time.
• Continue programming for each day of the
week.
• Touch
EXIT
to return to main screen.
TIP:
Pressing
Day
,
Time
or
Temperature
while
programming will shift focus to that setting,
allowing it to be edited in the order most
convenient for you.
5.2.1. COPY
COPY will copy the previous days programs into
the current day and advance the thermostat to the
beginning of next day.
6. ADVANCED FEATURES
6.1. FILTER USAGE MONITOR
The FILTER MONITOR is used to help determine
when your filter should be changed. It counts the
hours of HEAT and COOL since it was last reset
When the monitor limit is reached the CHANGE
FILTER indicator will become visible. The default
value of 720hrs is normally used for a 90 day filter.
Other values are given in the following table.
To Reset Filter Counter And/Or Change The
Counter Limit
• At the main menu touch
MENU
.
• SCROLL to FILTER USAGE.
• Touch
YES.
Filter Usage Count will appear.
• Touch
NEXT
. RESET will show.
• Touch
YES
to reset the counter and advance to
the filter limit menu, or touch
NEXT
to advance to
the filter monitor menu without resetting the
counter. Limit Hours will be flashing.
• Use
UP/DOWN
arrows to change limit. Set the
filter limit to "0" to disable the Filter Usage Monitor.
• Touch
YES
to accept new count value and
return to the filter counter menu. If a new limit is
set, the filter counter will be reset automatically.
• Touch
EXIT
to return to main menu.
6.2. SWING SETTING
A thermostat works by turning your heating or
cooling system on and off whenever the room
temperature varies a certain number of degrees
from the set-point temperature. This variation is
the "swing." Your system should cycle on about 3
to 6 times per hour. A smaller swing number
increases the number of cycles, so room
temperature is more constant. A larger swing
number decreases the number of cycles, saving
energy in most cases. To change the SWING value
from the main menu:
• Touch
MENU
.
• SCROLL to SWING VALUE.
• Touch
YES
. Adjust Swing Value will appear.
6
30
60
90
240
480
720
FILTER LIFE IN DAYS SET COUNTER HOURS TO