Filter
Top Products
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
6
NEW CONSTRUCTION OR RENOVATION
1. Select a location that is not prone to mois-
ture and is located at least 3 feet (or 0.9m)
away from combustible materials such as cur-
tains or drapes, furniture, bedding, paper, etc.
2. Place the unit in selected location to see
how it will look in the future.
3. Mark the desired location on the floor and
store unit in a safe, dry and dust free location.
4. Frame in an opening leaving at least 1/4"
(6mm) around the edge of the unit. Any new
wiring must be done in compliance with local
and national codes and other applicable regu-
lations in order to reduce the risk of fire,
electric shock or other injuries. Therefore, it is
strongly recommended that you hire a profes-
sional to complete any such work.
INSTALLING THE FIREPLACE INSERT
1. Once the site has been prepared, the fire-
place insert can be installed.
2. Make sure the switch is in the "OFF" position.
3. Plug the fireplace into a 15-amp/120 volt,
grounded outlet.
4. Push the fireplace insert so that the trim is
against the finished mantel or wall surface.
WARNING: GRILLS ON THIS ELEC-
TRIC FIREPLACE CANNOT, IN ANY
WAY, BE COVERED AS IT MAY CRE-
ATE A FIRE HAZARD.
Notes: Power supply service must be com-
plete prior to finishing, to avoid reconstruction.
Grills and air openings cannot be covered in
any circumstances.
OPERATING INSTRUCTIONS
The controls (
see Figure 4
) are located on the
bottom right corner of the unit.
1. Plug in your electric fireplace.
2. Main ON/OFF Power Switch: This switch is
located on the right side of the control panel
(
see Figure 4
). When the unit is on, the
default settings for the fireplace is HI ember
bed and flame and the heater is OFF.
Figure 4
3. Temperature Control Button and LED: This
button is located to the left of the Remote
Control Receiver (
see Figure 4
). The LED is
located to the right of the Flame Button. Push
button to cycle through the settings. When this
button is pushed, the LED will change to its
corresponding color; Green for LO, Orange for
MED, and Red for HI. When heater is on, heat
will emit through vents located above the fire-
box opening panel (
see Figure 6, page 7
).
The heater has a built in thermostat so it will
shut off automatically once the set tempera-
ture is reached. It will also turn on automati-
cally if the room temperature drops below the
set temperature.
Notes: When the heater is turned on for the first
time, it may release a slight, harmless odor.
This odor is a normal occurrence caused by the
initial heating of the internal heating elements
and should not occur again.
4. Flame Control Button: This button is lo-
cated to the left of the Temperature Button
(
see Figure 4
). After power is on, push the
Flame Control Button to adjust flame and em-
ber bed brightness. Press and release the
Flame Control Button to cycle through LO,
MED, HI and OFF.
OPERATING BY REMOTE CONTROL
(
see Figure 5
)
1. Plug in your electric fireplace.
2. Push the ON/OFF Power Button to turn unit
on. Power LED will light.
Flame Control
Button
ON/OFF Power
Button
Temperature
LED
Temperature
Control Button
Remote Control
Receiver
FL
TM
3. When operating the remote control, it must
be pointed at the sensor on the bottom PANEL.
4. The ON/OFF button at the top left of the
remote is the main ON/OFF power button.
Pressing this button activates the power to the
unit.
5. To adjust the ember bed lighting and flame
brightness, press the "—" or "+" FLAME but-
tons. There are six levels of brightness.
The HEATER button activates the heater. The
heater is pre-wet to the following temperatures:
HI will shut off when room reaches approxi-
mately 86° F (30° C). The LED will be red. MED
will shut off when room reaches approximately
75° F (24° C). The LED will be orange. LO will
shut off when room reaches approximately 64°
F (18° C). The LED will be green.
6. To turn off the fireplace, press the ON/OFF
button once. When you restart the fireplace e
with the remote control, all of the features you
had set will remain in effect. Notice: This
remote control must remain within 26 feet or
8 meters of the fireplace to be effective.
Note: Make sure your batteries are fully charged
and installed correctly in your remote control.
Figure 5
Indicator
Light
Infrared Ray Exit