Lennox Hearth LMBV-42RMN Indoor Fireplace User Manual


 
5
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
LENNOX MERIT
®
SERIES B-VENT GAS FIREPLACES • 42" LMBV MODELS • INSTALLATION INSTRUCTIONS
FRAMING SPECIFICATIONS
Figure 4
Figure 5
Figure 6
Framing Dimensions
Note: All framing dimensions calculated for
1/2" dry wall at the appliance face. If sheath-
ing the chase or finishing with other thickness
materials, calculations will need to be made.
TYPICAL INSTALLATION SEQUENCE
The typical sequence of installation follows,
however, each installation is unique resulting
in variations to those described.
1. Construct the appliance framing.
2. Route gas supply line to appliance location.
3. Position the appliance.
4. Install the vent system and exterior termination.
5. Field wire and install operating control switch.
6. Make connection to gas supply.
7. Install (optional) outside Air Kit.
8. Install the logs and rockwool.
9. Checkout appliance operation.
10. Adjust burner to ensure proper ame ap-
pearance.
PRE-INSTALLATION NOTES
The fireplace may be installed directly on a
combustible oor or raised on a platform of
an appropriate height. Do not place fireplace on
carpeting, vinyl or other soft oor coverings. It
may, however, be placed on at wood, plywood,
particle board or other hard surfaces. Be sure
replace rests on a solid continuous oor or
platform with appropriate framing for support
and so that no cold air can enter the room from
under the fireplace.
* When FOAK is used.
The fireplace may be positioned and then the
framing built around it, or the framing may be
constructed and the fireplace positioned into
the opening.
Usually, no special oor support is needed for
the fireplace, however, to be certain:
1. Estimate the total weight of the fireplace
system and surround materials such as brick,
stone, etc., to be installed.
2. Measure the square footage of the oor space
to be occupied by the system, surrounds and
hearth extensions.
3. Note the oor construction, i.e. 2 x 6’s, 2
x 8’s or 2 x 10’s, single or double joists, type
and thickness of oor boards.
4. Use this information and consult your local
building code to determine if you need ad-
ditional support.
If you plan to raise the fireplace and hearth
extension, build the platform assembly then
position fireplace and hearth extension on
top. Secure the platform to the oor to prevent
possible shifting.
INSTALLING THE FIREPLACE
Step 1. Frame appliance enclosure as illustrated
in Figures 4 through 7 on page 5.
Note: The nailing flanges, combustible framing
members and screw heads located in areas
directly adjacent to the nailing flanges, are
EXEMPT from the 1/2" clearance to combustible
requirements for the firebox wrapper. Combus-
tible framing may be in direct contact with the
nailing flanges and may be located closer than
1/2" from screw heads and the firebox wrapper
in areas adjacent to the nailing flanges. Frame
the opening to the exact dimensions specified
in the framing details of this manual.
Note: The framed depth, 21-5/8" (549 mm) from
a framed wall, must always be measured from
a finished surface. If a wall covering such as
drywall is to be attached to the rear wall, then
the 21-5/8" (549 mm) must be measured from
the drywall surface. It is important that this
dimension be exact.
If the appliance is to be elevated above oor
level, a solid continuous platform must be
constructed.
The header may rest on the top metal spacers,
but must not be notched to fit around them.
Consult all local codes.
Figure 7
Header
B
A
Fireplace Framing
C
A
G
Inside Chase
HH
Back Wall of Chase/Enclosure
Including Finising Materials
if any
Rough
Framing Face
(Unfinished Shown)
A
Outside Chase
G
C
Back Wall of Chase/Enclosure
Including Finising Materials
if any
Rough
Framing Face
(Unfinished Shown)
Corner Installation
J
D
C
A
E
G
F
Back Wall of Chase/Enclosure
Including Finising Materials
if any
Rough
Framing Face
(Unfinished Shown)
A 46-1/4" 1175 mm
B 43-1/2" 1105 mm
C 33" 838 mm
D 17-1/2" 445 mm
E 76-1/4" 1937 mm
F 38-1/8" 968 mm
G 21-5/8" 549 mm
H* 8" 203 mm
J 20-5/8" 524 mm
K 53-7/8" 1368 mm