Filter
Top Products
_iiii_i_ii_i SECTION2 _J_J_J:,_:,_] HOW YOUR WATER SOFTENER WORKS
A. FACEPLATE TIMER FEATURES
S
C
T
N
JJJJJJJJJJJJJJJJ.
J_JJJJJJJJJJJ_JJJ
JJJ_JJJ_JJ_JJ_
JJ JJJJ_JJJJ_
JJ JJJJJJJ_J
JJ J_JJJJJJJJ
J_ _JJJJJJJJ_
JJ _J_JJJJJJJ_
JJ _J_JJ
JJ _JJJJJ_JJ
JJJ_JJJJJJJJJJ_J_
JJJJ_JJ_JJ_JJ_JJ
• EXTRA RECHARGE
Sometimes, a manually started
regeneration (recharge) may be
desired, or needed. Two exam-
ples are:
- You have used more water than
usual (guests visiting) and you
may run out of soft water before
the next timer started regenera-
tion.
- You did not refill the softener
with salt before it was gone. After
you refill with salt:
You can start a regeneration right
away, or you can set the timer to
regenerate at the next 2:00 AM (or
other preset recharge time). Do
the following.
• RECHARGE NOW '_' _ _'_1" "
Press the ON/OFF-HOLD but- ;
ton and hold until *RECHARGE, ',
Serv and Fill begin to flash in the display. Upon
reaching fill, the first cycle of regeneration, the flash-
ing Serv goes off and Fill is on steady. RECHARGE
continues to flash. This regeneration will last for
about 2 hours. After the 2 hours, you will have soft
water again.
*Note:
If the CLEAN feature is set to ON, a cleaning back-
wash (CLEAN and Bkwsh or Rinse flashes in the dis-
play, along with the minutes of the clean cycle re-
maining) precedes the recharge.
• RECHARGE TONIGHT i /.uo /
Press and release (do not hold) the _,_ _o.,o.
ON / OFF-HOLD button. RE-
CHARGE TONIGHT flashes in the display, and the
softener begins regeneration at the next preset re-
charge time. Press and release the ON/OFF-HOLD
button once more if you decide to cancel the regen-
eration, and RECHARGE TONIGHZ
• SALT MONITOR SYSTEM
The face plate timer has a low salt monitor with an
indicator light to remind you to refill the storage
tank with salt. To set this monitor system:
_Lift the salt hole cover and level the salt in the
storage tank.
m
The salt level decal, on the brineweU inside the
tank, has numbers from 0 to 8 (see drawing be-
low). Observe the number the leveled salt is at
or closest to.
_I Now, press the SALT LEVEL ADJUST button
until black bars display up to the salt level num-
ber. For example, the pictures below show the
salt level at 6.
_ Finally, set the level you want the low salt indi-
cator light to come on. Press the SIGNAL LIGHT
ADJUST button until a (÷) shows opposite this
number. In the example below, the light will
come on when the stored salt drops to level 2. At
level 2, the storage tank is about 1/3 full. This is
the lowest you should allow the stored salt level
to drop to (see note on page 1-6).
_ If you wish to turn the salt monitor off, press the
SIGNAL LIGHT ADJUST button until OFF
shows above.
Note:
Your salt monitor is an estimate of your salt level; ac-
curacy depends on the type of salt used and other
regeneration characteristics.
salt
level
LEVEL u_V_
bars, salt SALT
level LEVEL 8
11116
brinewell
_4
decal _ 3
12_
_13($
RECI_ARGE
TONIGHT
RECHARGE
NOW
indicator light LOW
SALT
2-1
Problems, Questions? Call 1-800-426-9345 Kenmore Water Line