Filter
Top Products
E2008 CCN 15207673
(800) 276-4658 D FAX (800) 266-7016
fluids.ingersollrand.com
INGERSOLL RAND COMPANY LTD
P.O. BOX 151 D ONE ARO CENTER D BRYAN, OHIO 43506-0151
1” DIAPHRAGM PUMP
OPERATOR’S MANUAL
PM10X-X-X-A02
RELEASED: 2-28-05
REVISED: 5-19-10
(REV. 06)
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
1:1 RATIO (METALLIC)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
Refer to Model Description Chart to match the pump material options.
637397 for air section repair (see page 6).
637401-XX forfluidsection repair(seepage 4).NOTE: This kitalsocon-
tains several air motor seals which will need to be replaced.
637395-X major air valve assembly (see page 7).
PUMP DATA
Models see Model Description Chart for “-XXX”..............
Pump Type Metallic Air Operated DoubleDiaphragm..........
Material see Model Description Chart..............
Weight PM10A
-CSS-XXX-A02 44.84 lbs (20.3 kgs)... ...
PM10R
-CSS-XXX-A02 38.2 lbs (17.3 kgs)...
PM10S
-CSS-XXX-A02 51.64 lbs (23.4 kgs)...
Maximum Air Inlet Pressure 120 p.s.i.g. (8.3 bar).........
Maximum Material Inlet Pressure 10 p.s.i.g. (0.69 bar).....
Maximum Outlet Pressure 120 p.s.i.g. (8.3 bar)..........
Maximum Flow Rate
(flooded inlet) 52.2 g.p.m. (197.6 l.p.m.)....
Displacement / Cycle @ 100 p.s.i.g. 0.232 gal. (0.88 lit.)...
Maximum Particle Size 1/8” dia. (3.3 mm)............
Maximum Temperature Limits (diaphragm / ball / seal material)
E.P.R. / EPDM -60_ to 280_ F(-51_ to 138_ C).........
Polypropylene 35_ to 175_ F(2_ to 79_
C)
.........
SantopreneR -40_ to 225_ F(-40_ to 107_ C)..........
PTFE 40_ to 225_ F(4_ to 107_ C)...............
Dimensional Data see page 8................
Mounting Dimension 4”x 6.25”(101.6 mmx 158.8mm)........
Noise Level @ 70 p.s.i., 60 c.p.m. 80.6 db(A)
{.....
Thepump soundpressure levels publishedhere have beenupdated to anEquivalent
Continuous Sound Level(L
Aeq
) to meetthe intent of ANSIS1.13-1971, CAGI-PNEU-
ROP S5.1 using four microphone locations.
NOTICE: All possible options are shown in the chart, however, certain
combinations may not be recommended, consult a representative or the
factory if you have questions concerning availability.
Figure 1
MODEL DESCRIPTION CHART
PM10 X -C S S -X X X -A02
PM10X - CSS - X X X -A02
637401 - X X
DiaphragmBall
FLUID SECTION SERVICE KIT SELECTION
EXAMPLE: Model # PM10A-CSS-AAA-A02
Fluid Section Service Kit # 637401-AA
Seat Material
A - Santoprene
S - 316 Stainless Steel
Diaphragm Material
A - Santoprene
M - Medical Grade Santoprene
T - PTFE / Santoprene
Hardware Material
S - Stainless Steel
Fluid Caps & Manifold Material
S - Stainless Steel
Fluid Connection
C - 1-1/2” Tri-Clamp
Center Section Material
A - Aluminum
R - Polypropylene
S - Stainless Steel
Ball Material
A - Santoprene
T - PTFE
11-11-10
07)